User manual ASTAR LTV-3001 INSTRUCTION MANUAL

[. . . ] 30" TFT LCD TV INSTRUCTION MANUAL MODEL: LTV-3001 Please read all the safety and operating instructions carefully before you begin. Safety class This is an IEC safety class I product and must be grounded for safety. CONTENTS IMPORTANT SAFETY INSTRUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 PREFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WARNING AND CAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Improper installation may render the unit unsafe in the event of an earthquake. etc. 3. The unit must be installed concrete wall. Refer to drawings below: A Wall A -8- INSTALLATION FRONT (Power on/standby)indicator IR KEYS: 1. CH+: channel up select, it is equivalent . 7. POWER/ SIGNAL SELECT: press the key at least 5 seconds to turn off the set (standby). 8. (Power on/standby)indicator:Lights up in green when the set is working. when the standby mode, the indicator lights up flash. -9- INSTALLATION BACK Software upgrade Power Input SCALE 1. 000 Power switch VIDEO output and Audio output Av2 Input S-VIDEO Input AUDIO VIDEO OUT L/MONO R AV1 L/MONO R AV2 S-VIDEO IN VIDEO input and Audio input IN HDTV Audio Input YC Input Analog RGB Input DVI Input R PC AUDIO IN HDTV AUDIO Cb Cr Y VGA DVI L Pb Pr Y C US LISTED Audio/Video Apparatus E 58WJ 221338 -10- INSTALLATION PC STEPS: 1. Your TV can receive either 525i/60Hz or 625i/50Hz interlace signals. *Please keep AC cord unplugged when connecting TV system. -13- BATTERY INSTALLATION (REMOTE CONTROL) Insert Batteries Into the Remote Control 1. Replace with new batteries when the TV set begins to show the following symptoms: Operation is unsteady, erratic or when TV set shows no response to the remote control. Remark: 1. Remove batteries when they are exhausted or if the remote control has not been used for a long time. Do not mix new and old batteries of different types/brands. -14- REMOTE CONTROL DESCRIPTION 1 10 2 6 3 9 12 4 11 20 18 19 5 8 17 7 16 15 13 14 1. POWER (STAND BY) BUTTON ( ) Press this button to turn on or turn off (Standby mode). Press Power Button, picture and sound will appear on within a few seconds. 2. PROGRAM SELECTION BUTTON (0-9 BUTTONS) Push the number for your desired program and the program indicator will be displayed on the screen. 1. To input a one-digit number(0-9):press button to display"-", then press 0-9 digit button. 2. To input a two-digit number(10-99):press button to display "--", then press two digit button in order to input the channel number. For example, you need channel 25, please input "2" button followed "5" button. 3. To input a three-digit number(100-135):press button to display "---", then press three digit button in order to input the channel number. 3. VOL+/- BUTTONS (VOL+/-)(TV top control key) Press VOL+/- buttons to adjust sound level. -15- REMOTE CONTROL DESCRIPTION 4. CH+/- BUTTON(TV top control key) 1. Press the CH+/- button to select the program forwards. (Use these two buttons for Page Up/Down to increase/decrease page number in TELETEXT mode, option) 5. MENU BUTTON(TV top control key) Use "MENU" button for the tuning procedure, please refer to page19-27 for the details. 6. SLEEP BUTTON This key is used to set the sleep timer from 10 minutes to 240 minutes. Time will display on bottom-right corner and decrease in second when one minute left. To switch off this function, Press this key step by step until "off" display. 7. DISPLAY BUTTON Press this button to recall program number, system etc on the screen. 8. RECALL BUTTON Press this button to return to the previously viewed program. 9. SOURCE SELECT BUTTON ( ) (TV top control key) Press this button to display external video signal such as VCR or DVD player. *Remark: PC DVI TV AV1 AV2 S-VIDEO YCbCr HDTV 10. MUTE BUTTON ( ) Press once to mute the sound, press again to return to previous sound level. You can select STEREO/MONO/Dual A/Dual B or MONO/STEREO/SAP or FM/A2/Germem stereo/BTSC/Nicam by pressing the button. 12. PIP BUTTON The PIPfunction is workable when the main picture is only PC signal at 1024 at Full Screen 13. SOUND BUTTON Press this button is to select the sound mode:Personal/Cinema/Music/Speech. 14. PICTURE BUTTON Press this button to select the user picture mode:Personal/Bright/Mild/Standard. [. . . ] Canadian French Lanuage Ratings: E:Exempt G:Children 8ans+: Children 8 years and older 13ans+:Children 13 years and older 16ans+:Viewers 16 years and older 18ans+:Adult programming SETUP SETUP <Left> or <Right> key to change The 1. Language --- press or to select language OSD Position --- press or to select the display position of OSD. If parts of the top and bottom of the screen are cut off, press or to adjust the position of the image on the screen. Smart Fill screen Cinema Wide 14:9 4:3 -21- OPERATION INSTRUCTIONS 5. Timer Setting --- press to enter the menu , it is equivalent to the Sleep button. [. . . ]