User manual ASKO 1355

[. . . ] Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, cooking oils, other flammable or explosive substances as they give off vapors that could ignite or explode. Before the appliance is removed from service or discarded, remove the door to the drying compartment. Do not install or store this appliance where it will be exposed to the weather. Do not attempt to repair or replace any part of the appliance or perform any servicing unless specifically recommended in this guide. [. . . ] The power must be on before you can start the machine. until the Stop indicator light goes off (approximately 3 seconds). You will have to reselect a program and press Start to restart the dryer. LED WINDOW The LED window displays the program number for the Sensidry programs, as illustrated below: PROGRAM PROGRAM KNOB Turn this knob to select a program. 12:00 Position ­ This is where the line on the knob aligns with the line above the knob. When the knob is in this position, "00" displays on the LED to indicate no program has been chosen. P1 The corresponding program numbers are: Heavy = P1 Normal = P2 Delicate = P3 Iron Dry = P4 STAR BUTTON ART START BUTTON After you have selected a program and the desired options, press this button to start the dryer. The indicator light will go off when the program ends or has been cancelled. When you select Timed Dry, the LED displays the number of minutes selected, plus the cool-down time, as illustrated below: 20 When you select Air Fluff, the LED displays the number of minutes selected, as illustrated above. With both programs 5 and 6, as the program advances, the LED displays the remaining time. "C" indicates the program is in the cool-down cycle. STOP BUTT UTTON STOP BUTTON You can stop or cancel a program by pressing and holding the Stop button until the dryer stops. When you press Start, the program will start from the beginning. INTERRUPTING INTERRUPTING OR CANCELLING PROGRAM A PROGRAM To interrupt a program, simply open the door. To cancel a program, press and hold the Stop button Page 14 PROGRAMS PROGRAMS The Heavy, Normal, Delicate and Iron Dry programs are automatic (Sensidry) programs designed for certain types of loads, as defined in the table below. It is important, therefore, to select the appropiate program for the type of load you are drying. If you prefer, you can select Timed Dry, which does not When using Timed Dry, it's best to use a shorter time; then if the load isn't dry, you can set the timer for a few more minutes. This sensor turns off the heat when the laundry has reached the appropriate dryness. activate the humidity sensor. You should be careful when using this option not to overdry the fabrics. This program automatically uses the Low temperature setting, but you can change it to Normal by depressing the Temperature button. SIGNAL Press this button to set a signal to sound for three seconds when a program is complete. If you selected the Wrinkle-free option, the signal will sound every time the drum rotates. PROGRAM MEMORY PROGRAM MEMORY The dryer is designed to retain the settings last selected with each program. For example, if you select Normal, the Low temperature option, a 2-hour anti-crease, and Quick cool-down, next time you select Normal these options will automatically be selected. QUICK COOL-DOWN Every program, except Air Fluff, ends with a cool-down cycle that tumbles the clothes without heat to reduce wrinkling. The Cool-down button lets you choose between the Normal cool-down cycle (15 minutes) or a Quick cool-down cycle (5 minutes). The indicator light will stay lit when Quick is selected. STAR FEATURE ART CHILD-SAFE START FEATURE You can program the dryer not to start unless the Start button is held down for three seconds. Press the Start button five times in succession then press the Wrinkle-free button five times. Within three seconds, press the Wrinkle-free button again to select Child-safe start. The LED will display "3" to indicate the Child-safe start is active. (If the child-safe start has already been activated, "0" will display after you press the Wrinkle-free button. ) CHANGING OPTION SETTINGS You cannot change the option settings after you have pressed Start. [. . . ] If all of the above options are eliminated, the overheat protection has probably been activated. See "Overheat Protection" on page 3 for possible causes and instructions on how to restart the unit. My clothes are coming out wrinkled. You should remove the clothes as soon as the dryer signals the end of the cycle. If you can't remove the clothes right away, use the Anti-crease option. Try using a lower wash temperature, especially for permanent press and delicate items. The machine starts but it stops when I release the power button. The overheating protection has probably activated. [. . . ]