User manual ASK PROXIMA PRO AV 9320

[. . . ] 2 Register with ASK Proxima. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote Controller General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Preparing the Remote Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 5. After checking to make sure that the POWER/STANDBY indicator has stopped flashing amber and remains lit, unplug the AC power cord from the power outlet. This causes the POWER/STANDBY indicator to go out. After ensuring that the projector and the connected computer or video device are turned off, disconnect the connecting cables from the projector and the connected device. Close the lens cover. Auto Power Off Auto Power Off automatically turns off the projector whenever there is no input signal, and no operation is performed on the projector for about 30 minutes. When Auto Power Off is triggered, the projector first enters a cool down state, the same as it does when you press the [ ] (power) key to turn it off. While Direct Power On (page 11) is enabled, the projector will turn off automatically if no key operation is performed and no signal input is received within about 10 minutes after it is turned on. 12 Projector Basics Projector Basics For detailed information about projection operations, see the Reference Guide on the CD-ROM that comes with the projector. Selecting the Input Source When you turn on the projector, it first checks the RGB terminal for an input signal and then the VIDEO terminal. When it detects an input signal, it automatically selects it and starts projecting the signal. Whenever you want to manually trigger an input source search operation, press the [INPUT] key. When the projector detects an input source (RGB, component, or VIDEO) after an auto or manual select operation, the name of the newly selected source will appear in the projected image for a few seconds. The message "No signal input. " will appear if no input signal can be selected. Adjusting the Projected Image To adjust the size of the projected image Hold down the [ZOOM +] key to increase the size of the image or the [ZOOM ­] key to decrease it. When the image is the size you want, release the key. Projector key operation Press the [ZOOM] key and then hold down the [ ] key to increase the size of the image, press the [ZOOM] key and then hold down the [ ] key to decrease it. When the image is the size you want, release the key. To adjust image focus Hold down the [FOCUS the key. ] or [FOCUS ] key. When the focus is the way you want, release Projector key operation Press the [FOCUS] key and then hold down the [ ] or [ ] key to focus. When focus is the way you want, release the key. 13 English Projector Basics Auto Adjustment of an RGB Image When the input source is RGB (computer), the projector automatically adjusts vertical and horizontal positioning, frequency, and phase whenever it detects an RGB signal (following input source selection, power up, etc. ). You can also execute an automatic adjustment operation by pressing the [AUTO] key. You can turn off auto adjustment when you want to disable auto adjustment and maintain manual settings. If you unplug the AC power cord while the fan is still operating, an error may occur when you plug the AC power cord back in. Indicator/Error Message Description and Required Action POWER : Green steady The projector's internal temperature is very high. Press the TEMP :­ [ESC] key to clear the warning message and perform the LAMP :­ following steps. Check for any blocking of the projector's intake vents and Message : Internal temperature exhaust vents, and make sure that there is sufficient space is too high. projector air vents for If there is dust accumulated around the intake vents and/or blockage. exhaust vents, turn off the projector and remove it. 16 Troubleshooting Indicator/Error Message POWER : Amber flashing Amber steady TEMP : Red flashing (1-second interval) Turns off LAMP :­ Message : Internal temperature is too high. Description and Required Action Power has turned off automatically due to internal overheating. Check for any blocking of the projector's intake vents and exhaust vents, and make sure that there is sufficient space around the projector. If there is dust accumulated around the intake vents and/or exhaust vents, remove it. If there is no problem with the projector's vents, confirm that the POWER/STANDBY indicator is lit amber (without flashing), and then turn power back on again. If the error occurs again when you turn power back on, contact ASK Proxima service at www. askproxima. com/service Power has turned off automatically due to internal overheating. [. . . ] Use the setup menu to change the "Input Settings RGB Input" setting to "Auto" to correct the problem. Replace the battery (see "Replacing the Remote Controller Battery"). Make sure the remote controller is within the allowable range when you operate it. See "Error Indicators and Warning Messages" under "Indicators". [. . . ]