User manual ASK PROXIMA LIGHTBOOK 30

[. . . ] VHS Video In L R In­Audio­Out O I 10 A M P 12 11 10 9 Figure i-5 The Lightbook projector and Cyclops Remote Control 1 2 3 4 5 6 7 Internal Speakers Control Panel Cooling Fans Release Button Keystone Adjustment Focus Ring Remote Control IR Lens 8 Cyclops Remote Control 9 Circuit Breaker 10 Power Cord Receptacle 11 Main AC Power Switch 12 Connector Panel 13 Cyclops Quick Remote i-4 Introduction CONNECTOR PANEL All connections between the projector and computer or video source are made on the side connector panel. 1 2 3 4 5 67 8 Serial Computer In Monitor Out S-Video Video In L R In­Audio­Out O I 10 A M P 11 Figure i-6 The Connector Panel 10 9 CONNECTOR 1 SERIAL DESCRIPTION Connects to your computer so you can use Cyclops F/X software. Turns the projector on or off. 2 3 COMPUTER IN MONITOR OUT 4 5 S-VIDEO VIDEO IN 6 L-AUDIO-R 7 8 AUDIO IN AUDIO OUT 9 10 11 AC CIRCUIT BREAKER AC PLUG AC POWER Your Proxima Lightbook Projector i-5 CONTROL PANEL Use the Lightbook projector's control panel keys to turn the projector on or off, adjust the projected image, and display and hide the menu. and Over-Temperature 1 Replace Lamp 6 7 Source 2 3 Setup Menu 5 4 Figure i-7 The Control Panel KEY 1 FUNCTION Controls the menu and adjusts screen position. 2 Source Switches the video inputs. 3 Setup Activates the Setup menu. 4 Menu Displays or hides the menu. 5 Turns the lamp on or off. 6 7 Adjusts the volume. i-6 Introduction LIGHT FUNCTION Glows red to warn of an over-temperature condition. Flashes quickly if the projector is not fully opened. QUICK START Follow the appropriate section below for the type of system that you have. [. . . ] Clears the screen and provides a dark background for the Draw tool. 2 The Draw toolbar appears in the upper left of the display. Figure 2-15 Toolbox 3 The current tool (Pencil or Eraser) is highlighted and a cursor appears. Use the remote control to draw on the screen. 2-14 Chapter Two Draw Tool Bar The Draw tool bar has four options: Pencil Click to select the Pencil tool. This button also shows the currently selected color. Choosing a Color 1 Click New Color or the down arrow in the upper right corner of the Draw tool bar to display the color palette. Figure 2-16 Toolbox Color palette 2 Click the color you want to use. The Color box takes on the selected color, and the color palette remains on the screen. 3 Click the Color box or the down arrow in the upper right corner again to turn the color selection boxes off. Using the Lightbook Projector 2-15 4 To draw, click and hold the center of the MouseDisk at the desired starting point for about 2 seconds to lock it. Then, press the edges of the MouseDisk to move the Pencil tool and draw on the screen. 5 To exit Draw, click the small box in the upper left corner of the Draw tool bar. With the remote control, click and hold the center of the MouseDisk with the cursor on the top of the tool bar. Drag the bar to the new location and release the center button. Setting the Timer Use the Timer menu to start and reset the on-screen digital timer. You can set the Timer to count down for breaks, class activities, and other presentation requirements. 99:00 Reset Start Figure 2-17 Timer menu 1 From Tool Select, choose Timer and press the key. 2 Use the v and w keys on the control panel or the MouseDisk on the remote control to set the time. to start or stop the timer count down. 2-16 Chapter Two Reveal Use this feature to slowly reveal a screen for greater audience impact. Select Mono when using a monaural source for simulated stereo output. Using the Audio Menus You can include audio in your presentation in a variety of ways. Selecting Stereo Audio 1 Open the Fine Audio menu and select Stereo. 2 Press MENU to exit. Muting Audio with the Menu 1 Open the Audio menu. 3 Press MENU to exit and mute the audio. 2-22 Chapter Two Simulating Stereo While Using a Monaural Source 1 Open the Fine Audio menu. 2 Press MENU to exit. NOTE: If you are using a monaural source, it must be connected to the L-AUDIO input. Preferences Menu Use this menu to tailor the projector to your personal presentation style. Menus Tools Input Source Image Audio Fine Audio Preferences Prog. Key1 LightBoard WhiteBoard BlackBoard Timer Reveal Freeze Host Prog. Key2 LightBoard WhiteBoard BlackBoard Timer Reveal Freeze Host Operation Mode Normal High Altitude Advanced Help Figure 2-23 Preferences menu MENU ITEM SETTING Prog Key 1 and 2 Assigns a specific projector function to one of the PROG keys on the Cyclops Remote Control or to the Select key on the Cyclops Quick Remote. Operation Mode Select High Altitude to run the projector fans at higher speed. Use this setting if you are at a high altitude location or in a warm room. To set the PROG 1 or 2 keys, use the v, w, and keys on the Cyclops Remote to select the function that you want to assign to each PROG key. The Select key on the Cyclops Quick Remote will select the feature assigned to the PROG 2 key in the Preferences menu. Using the Lightbook Projector 2-23 Advanced Menu Use the Advanced menu to adjust the projector settings to suit a particular presenter's style and taste. Menus Tools Input Source Image Audio Fine Audio Preferences Language English Deutsch Francais Español Italiano Projection Front Rear Ceiling Rear-Ceiling Reset Mode None Selected Current Computer/Video Mode All Custom Computer Mode All Standard Computer Mode Factory Reset Advanced Help Figure 2-24 Advanced menu MENU ITEM Language Projection Reset Mode FUNCTION Display the menus in any of five languages. Select Reset to return the settings for the current image source to the factory defaults. 2-24 Chapter Two Help Menu Select Help from the Main menu to display connection diagrams for your PC, Macintosh, or video source. Help Topics PC Mac Video Figure 2-25 Help menu 1 Press v or w to select the item you want Help on. Press item, or to cancel. to display that Serial Computer In Monitor Out S-Video Video In L R In Audio Out SERIAL VIDEO/VGA AUDIO SERIAL VIDEO/VGA AUDIO Figure 2-26 PC Help screen Using the Lightbook Projector 2-25 Chapter 3 Cyclops F/X Your projector comes with Cyclops F/X -- software effects that you can use to make your presentations more interesting and effective. [. . . ] If the lamp fails and the indicator glows, allow the fans to cool the projector until they stop. If the lamp fails but the indicator does not go on, press the key to turn the lamp circuit off. Then, allow the fans to cool the projector until it stops. Maintenance 4-1 REPLACING A BULB 1 Pull the lamp assembly out as shown in Figure 4-1. Insert a new bulb, being careful to avoid bending the pins. NOTE: Avoid touching the bulb with your fingers. [. . . ]