User manual ASK PROXIMA IMPRESSION 860

[. . . ] USER GUIDE IMPRESSION 860 Not the actual front page 801. 318 USG/860/AE-A 30. 09. 96 USER GUIDE IMPRESSION 860 USER GUIDE LCD PROJECTOR 2 USER GUIDE LCD PROJECTOR TABLE OF CONTENTS 1 SYMBOL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This will scale the source resolution to fit the LCD screen resolution by adjusting the number of vertical and horizontal pixel lines at intervals throughout the image. 20 USER GUIDE LCD PROJECTOR POSITION OPERATION · Select POSITION. · Adjust using the cursor keys until the full image lies within the viewing area (see illustration). CONTR BRIGHT · Adjust using the contrast up/down arrow keys for optimum image quality · Adjust using the brightness up/down arrow keys for local lighting conditions. Your LCD projector is now fully set up and ready for use. If you experience any problems in carrying out this set up procedure you should refer to the section called Trouble-shooting found later in this user guide. 21 USER GUIDE LCD PROJECTOR 7 USING THE LCD PROJECTOR The LCD projector has a set of features and functions with which you need to be familiar with in order to operate the unit efficiently and to allow you to make a smooth, problem-free presentation. 7. 1 INFRARED REMOTE CONTROL The infrared remote control is the main user interface with the projector. The remote control is used to set the LCD projector correctly so that the best viewing conditions are achieved, and also to control your presentation. The functions performed by the keys on the remote control are described below. ON/OFF CONTR BRIGHT TUNE RESET SOURCE 1 SOURCE 2 SOURCE 3 FREEZE BLANK REAR FREQUENCY POSITION SCALE PAN OSD RIGHT DRAG LEFT 22 USER GUIDE LCD PROJECTOR The MEM column indicates whether the function setting is memorized for the source apparatus for future use. KEY CONTR FUNCTION Contrast is the ratio between light and dark colors. Low contrast is recommended for long-term viewing, while high contrast is used to enhance details. Brightness (whiteness) of the image can be altered to suit local lighting conditions. An unstable image can be seen as sideways instability or ` swimming' . Provided that the frequency setting is also correct, the ` swimming'can be removed by adjusting TUNE (See section Image Adjustments for illustration). KEY TYPE scale (up/down arrows) MEM Yes BRIGHT scale (up/down arrows) Yes TUNE scale (up/down arrows) Yes ON/OFF toggle - RESET SOURCE 1 SOURCE 2 SOURCE 3 single touch activated 3 source keys are mutually exclusive No No No 23 USER GUIDE LCD PROJECTOR KEY FREEZE BLANK REAR FUNCTION Holds the image projected on the screen. This feature can be used to hide actions on the computer that the audience need not see, such as changes between software packages, or for returning the audience' attention back to s the presenter!Mirrors the image for use when the LCD projector is incorporated into rear projection systems. It is provided for initial set-up using a source, and for adaption to special graphics adapters that are close to those in the compatibility list. An incorrect frequency setting can be seen as an image too wide or too narrow, combined with vertical, unstable bands. Select POSITION and then use the cursor keys to locate the projected image within the viewing area. See section Image Adjustments for illustration. KEY TYPE any key to release MEM No any key to release toggle No Yes FREQ scale (right/left arrows) Yes POSITION cursor movements Yes 24 USER GUIDE LCD PROJECTOR KEY SCALE PAN OSD CURSORS RIGHT DRAG LEFT FUNCTION Selects direct 1:1 mapping or scaling of images. Use the cursor keys to show different areas of the image based on each of the four corners. Displays the On-Screen Display (OSD) information at the foot of the screen. The four cursor keys simulate the actions of the desktop mouse to control the computer cursor. Emulates the left mouse key. KEY TYPE toggle cursor movements MEM No - toggle No cursor movements - - - 25 USER GUIDE LCD PROJECTOR 7. 2 TOP PANEL KEYBOARD The settings most likely to be adjusted during the set-up process are also accessible via a secondary keyboard panel on the top of the LCD projector, known as the Top Panel Keyboard. The buttons function exactly as the corresponding remote control keys, with the exception of TUNE which uses a single button to adjust settings in a wrap-around scale. LCD PROJECTOR ON/OFF TUNE BRIGHT RESET 26 USER GUIDE LCD PROJECTOR 8 SPECIAL FEATURES OF YOUR LCD PROJECTOR INTELLIGENT COOLING SYSTEM 8. 1 The fan operates as long as the LCD projector is switched on. [. . . ] The image is not compressed and cannot be panned around using the remote control. 38 USER GUIDE LCD PROJECTOR 11. 6 CONNECTORS ON THE SUPPLIED CABLES The connectors on the supplied cables are described below. CABLE VGA 4m/13ft Ysplit cable PROJECTOR END 26 pin HDDSUB male with fingerscrews SOURCE END 1 2 (if applies) Computer end: Monitor end: 15 pin HDDSUB 15 pin male with HDDSUB fingerscrews female with nuts Mouse cable 8 pin mini DIN male 8 pin mini DIN male - Mouse adapter cable (serial) 8 pin mini DIN female Computer end: 9 pin DSUB female with fingerscrews Computer end: 4 pin mini DIN female (MAC ADB style) Mouse end: 9 pin DSUB male with nuts MAC mouse adapter 8 pin mini DIN female Mouse end: 4 pin mini DIN female (MAC ADB style) 39 USER GUIDE LCD PROJECTOR 12 CONNECTORS The connector ports for the source equipment on the LCD projector are located on the right hand-side (when facing) of the unit. The connector port for the mains power cord is located next to the fuse cabinet. The pinouts of all the connector ports is described in this section. Do not connect any devices or cables other than those supplied with the LCD projector into the connector ports on the projector unit, even if the connector ports appear identical, as this voids any warranty and may cause permanent damage to the projector. SOURCE 1 SOURCE 2 SOURCE 3 MOUSE 12. 1 SOURCE 1/2/3 These connectors relay all sync signals from the computer to the projector, and also to a local CRT monitor if required. 9 18 26 1 2 3 4 5 6 7 8 9 ANALOG R IN ANALOG G IN ANALOG B IN NOT USED NOT USED NOT USED ANALOG R OUT ANALOG G OUT ANALOG B OUT 10 11 12 13 14 15 16 17 18 1 10 19 26 PIN HIGH DENSITY DSUB FEMALE (FRONT VIEW) ANALOG R GND IN ANALOG G GND IN ANALOG B GND IN NOT USED NOT USED NOT USED ANALOG R GND OUT ANALOG G GND OUT ANALOG B GND OUT 19 20 21 22 23 24 25 26 HSYNC IN C/VSYNC IN DIGITAL GND PCID0 PCID1 DIGITAL GND HSYNC OUT VSYNC OUT 40 USER GUIDE LCD PROJECTOR 12. 2 MOUSE This port is used to exchange mouse messages between the projector and the computer. 7 8 5 4 6 3 8 PIN MINIDIN FEMALE (FRONT VIEW) 1 2 3 4 MAC ADB PS/2 CLOCK PS/2 DATA RS232 TXD 5 6 7 8 RS232 RTS RS232 RXD RS232 CTS GND 2 1 41 USER GUIDE LCD PROJECTOR 13 ENVIRONMENTAL STATEMENT Care has been taken in the manufacture of this LCD projector that environmental stress and pollution has been minimized. [. . . ]