User manual ASK PROXIMA DP5800

[. . . ] Liquid Crystal Projector Model DP5800 USER'S GUIDE Please read this user's guide for fast setup and use of your new projector. After reading this guide, keep it in a safe place for future reference. DP5800 Features High brightness Highly efficient optical system with a metal halide lamp ensures high brightness. High resolution Three separate high-definition liquid crystal panels are used to provide sharp, clear pictures. Compact size and light weight for portability RGB output terminal RS232C communication Mouse emulation Power zoom and power focus Contents Page Symbols Used in this Guide . . . [. . . ] If the polarities are not correct, it may cause injury or damage near the unit due to a battery explosion or liquid leakage. Caution Cautions on remote control use · Do not drop the remote control or apply any shock to it. · Do not let the remote control get wet and do not put it on a wet object. · If you are not going to use the remote control for a long time, remove the batteries from it. · If operation of the remote control becomes difficult, replace the batteries. 7 Installation Projector and screen setup Determine proper picture size and projection distance as illustrated below. Top view Screen Side view Lens center b a Screen (inches) 40 60 80 100 120 150 200 a (inches) Minimum Maximum 60 89 119 149 179 224 298 89 134 179 224 269 336 448 b (inches) 3. 4 5. 1 6. 9 8. 6 10. 3 12. 9 17. 2 a: Distance from the projector to the screen b: Length from the center of the lens to the bottom of the picture Using the foot adjusters Adjust the projection position using the foot adjusters at the bottom of the projector. Front view Side view In = unlock Out = lock Foot adjuster Viewing angle can be changed from 1° ~ 7°. 1. Adjust the feet to the best viewing angle, and then lock the foot adjusters. Caution Do not unlock the foot adjusters unless you are supporting the projector, to avoid dropping the projector and causing an injury. If the foot adjusters do not lock completely, move the foot slightly before locking. 8 Using the Projector Projecting the picture 4 275 2 4 ZOOM RIGHT RISET RESET STANDBY/ON MENU FOCUS 5 TIMER VOL BLANK 1 3 7 POSITION MUTE VIDEO1/2 RGB1/2 INPUT 1 2 3 4 5 6 7 Turn the MAIN POWER switch of the projector on. [ : ON] · The ON indicator will glow orange. Press the STANDBY/ON button. · The ON indicator blinks (green) and then glows (green). Remove the lens cap. Adjust the focus using the FOCUS buttons. (1) Press the FOCUS button. (2) Press the Focus +/- buttons until the picture is clear. +++FOCUS+++ Turn on all connected equipment. See pages 17-19 for the correct sequence for turning on various equipment. Press the INPUT button or the INPUT SELECT (VIDEO or RGB) button to select the source of the projected signal. · The selected signal input source is displayed at the bottom right of the screen. NOTE: Video 1/2 works with video capable units only. RGB 1 9 Using the Projector (continued) Turning off the power 1 1 2 RIGHT RISET RESET STANDBY/ON MENU 3 1 Press and hold the STANDBY/ON button for 1 second. · The ON indicator lights up orange and the lamp turns off. NOTE: If you press the STANDBY/ON button for less than 1 second, the projector will not switch to Standby mode. 2 3 Turn the MAIN POWER switch of the projector off. [ Replace the lens cap. : OFF] Caution Do not turn off the projector's MAIN POWER switch before pressing the STANDBY/ON button. After the STANDBY/ON button is pressed, the fan will run for about 1 minute to cool the projector. 10 Projector Messages and Indicators On screen display The following messages may be displayed on the screen. Message NO SIGNAL IS DETECTED SYNC IS OUT OF RANGE CHANGE THE LAMP Check the input signal connection. The horizontal frequency of the input signal exceeds the range of the projector, and it cannot be displayed. Action Indicator display The ON indicator, LAMP indicator and TEMP indicator will light or blink in the following cases. Indicator status Lights orange ON indicator Blinks green Lights green Blinks orange Lights red LAMP indicator Blinks red Lights red TEMP indicator Blinks red Cooling fan failure Service the projector. Meaning Standby mode Warming up Normal operation Cooling down Lamp cannot light Action -------------- ------------ -------------- ------------ -------------- ------------ -------------- ------------ Cool projector by power off for 20 minutes. The LAMP indicator will light when the lamp becomes too hot. If the LAMP indicator still glows red, contact your dealer. 11 Using the Menus 2, 3 3 RIGHT RIGHT RISET RESET 2 1 MENU 1 menu STANDBY/ON 1 2 3 4 Press the MENU ( ) button or the MENU ON / OFF button. · Menus are displayed on the screen. Select the menu to be adjusted using the MENU ( buttons or the MENU STICK SWITCH. · The menu displayed in green is selected. ) Select the item to be adjusted using the MENU ( buttons or MENU STICK SWITCH. · The item displayed in green can be adjusted. ) The changes take effect. Storing your settings Settings can be saved for the VIDEO1, VIDEO2, RGB1 and RGB2 input terminals. These adjustments are saved after projector power is turned off. To return to the initial settings · Select the menu item to restore to the initial setting using the menu buttons or menu stick switch. · Select DEFAULT · Select the item to restore to the initial setting. · Press the RESET button a second time. SETUP VOL BRI CON SHA COL TIN INPUT IMAGE OPT. RESET `SETUP' DEFAULT CANCEL 12 Using the Menus (continued) SET UP Menu The SET UP menu lets you change the picture characteristics and position. The menus will be different for RGB and video signals. RGB signal Setup mumu SETUP INPUT IMAGE OPT. VIDEO signal Setup menu (video models only) SETUP INPUT IMAGE OPT. VOLUME BRIGHT CONTRAST V. POSIT H. POSIT H. PHASE H. SIZE 121 57 7 800 VOLUME BRIGHT CONTRAST SHARPNESS COLOR TINT Item VOLUME BRIGHT (BRIGHTNESS) CONTRAST SHARPNESS* COLOR* TINT* V. POSIT (V. POSITION) H. POSIT (H. POSITION) H. PHASE H. SIZE * Video models only Decrease Dark Lower Soft Less Red Range Increase Bright Higher Sharp More Green Moves the picture up or down. [. . . ] The projector replies with '70H' + '70H' 10 times, every 1 second. When projector receives '70H' + '70H', it replies '12H' + '03H' + '01H' + '00H'. If the interval of bytes exceeds 500mS, the projector replies with '70H' + '70H'. If there is no command from the computer, the projector treats it as a framing error. [. . . ]