User manual ASK PROXIMA DP2300

[. . . ] In all cases, the product has undergone testing and quality inspection, and Proxima's full warranty terms apply. The end-user's sales receipt or invoice showing the date of purchase of the product and the name of the Reseller is proof of date of purchase. The Warranty extends only to the original purchaser and is not transferable. During the Warranty Period, Proxima will, at no additional charge, repair or replace defective parts or at the option of Proxima, replace the entire unit. Limitation of This limited Warranty does not extend to any Proxima product that has been damaged or Warranties been rendered defective (a) as a result of accident, misuse or other abuse; (b) by the use of parts not manufactured or sold by Proxima; (c) by modification of the product; or (d) as a result of servicing by non-authorized personnel. [. . . ] Unplug the monitor cable from your computer's video monitor port and attach it to the MONITOR end of the Y-cable. Note: To connect your desktop computer without a monitor, connect one of the supplied video terminators to the MONITOR end of the Y-cable. Locate the Y-cable's common end, marked CPU/MAC II for Macintosh systems and COMPUTER/VGA for IBM­ compatibles. Plug it into the computer's monitor port. User's Guide · 2­9 Chapter 2 · Detailed Setup 4. Insert the Y-cable's large, 25­pin connector (marked LCD) into the Desktop Projector's COMPUTER port. MONITOR PROXIMA LCD COMPUTER /VGA Figure 2-9 VGA connections MONITOR PROXIM A MAC II/CPU LCD Figure 2-10 Macintosh connections 2­10 · User's Guide Chapter 2 · Detailed Setup Notebooks/Laptops Use the Y-cable appropriate for your system. For IBM compatibles, use part number C454-6; for Macintosh systems, use part number C464-6. If you are using your notebook or laptop computer with an external monitor, follow the procedure described in the section titled Desktop Computers. Locate the Y-cable's common end, marked CPU/MACII for Macintosh systems or COMPUTER/VGA for IBM compatibles. Insert the Y-cable's large, 25-pin connector marked LCD into the projector's COMPUTER port. Attach the appropriate video terminator to the MONITOR end of the Y-cable. For IBM compatibles, use part number C936; for Macintosh systems, use part number C935. Note: If your Desktop Projector is unable to project an image at the same time your laptop monitor displays an image, refer to your laptop documentation for information on switching between the internal screen and the video port. Special Configurations If your computer has an internal monitor but no external video capability (such as Macintosh Performa 575, PowerMac 5200, and certain PowerBooks), you need a video adapter card in order to attach the projector. Setup for a third-party adapter is identical to the procedures outlined in the previous section Desktop Computers. Connect speaker A to speaker B using the cables supplied with the speaker system. Note: The projector's internal speakers can't be disabled or turned off. 2­16 · User's Guide Chapter 2 · Detailed Setup PROXIM A A B Figure 2-12 Connecting the Desktop Projector to external speakers External Stereo System To connect your Desktop Projector to an external stereo system: 1. Using the computer audio cable (C498­6), insert the mini jack end into the projector's AUDIO OUT connector. Insert the RCA connectors at the other end of the cable into the external amplifier's left and right AUDIO IN connectors. User's Guide · 2­17 Chapter 2 · Detailed Setup PROXIM A IER PLIF / AM T IVER RIGH ECE LEFT EO R STER Figure 2-13 Connecting the Desktop Projector to an external stereo system Powering Up Your Desktop Projector and external monitor (if you are using one) must be turned on before you turn on your computer, so that the computer properly senses each display during its boot-up sequence. Applying Power to the Projector On the rear connector panel of the projector, you'll find a power cord receptacle and an AC POWER switch. 2­18 · User's Guide Chapter 2 · Detailed Setup 3 2 1 Figure 2-14 Power receptacle (1), AC POWER switch (2), and circuit breaker reset switch (3) To power up the projector: 1. Plug the power cord into the Desktop Projector's power receptacle at the rear of the unit. CAUTION!Plug the AC power cord into the Desktop Projector BEFORE connecting it to an electrical outlet. If you plug the power cord into the wall first, you might damage the projector. Connect the power cord to a properly-grounded wall outlet or surge protector. To raise or lower the projected image, tilt the mirror assembly to the appropriate angle. User's Guide · 2­19 Chapter 2 · Detailed Setup CAUTION!Locate the air intake and exhaust grills on the top cover and to the left and right sides of the projection mirror assembly, and the exhaust grills on the rear panel and side of the projector. Never operate the projector if these grills are clogged or obstructed, or if the electric fans are not running. Figure 2-15 Allow for proper air flow! CAUTION!In particular, the ceramic socket at the lamp's base can get extremely hot! [. . . ] · To clean a filter, wash it in a mild solution of soapy water, rinse and let it dry. · To replace a filter, refer to Appendix B for ordering information. Reassemble the air filter grill assemblies and replace them. Top Air Intake Filter Assembly 1. To release the top air filter assembly, place both thumbs into the two depressions located on the rear of the top filter grill assembly frame. [. . . ]