User manual ASK PROXIMA C110

[. . . ] DLP Projector TM USER'S USER'S GUIDE GUIDE WARNING: This product contains chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. WARNING: This product has a lamp which contains a very small amount of mercury. Dispose of it as required by local, state, or federal ordinances and regulations. For more information, see www. eiae. org This entire user's guide is available on the enclosed CD as an Adobe Acrobat pdf file in the following languages: English, French, German, Italian, Norwegian, Portuguese, Spanish, Russian, Japanese, Korean, Traditional Chinese, Simplified Chinese. [. . . ] If the projector has been working exceeded its lamp life (page 42), replace the lamp and reset the lamp timer. An unidentifiable error: please contact your dealer Power Save The projector also has a Power Save feature that automatically turns the lamp off after no active sources are detected and no user interaction with the projector is performed for 20 minutes. See page 39. blinking green Turning off the projector You can turn the projector off simply by toggling the power switch to the off position. You can also press the remote's Power button to place the projector in the Off state while it is running. When the Power button is pressed twice (once to start the power-down process and a second time to verify that you want to power the projector off), the lamp turns off and the LED blinks green for one (1) minute while the fans continue to run to cool the lamp. While the LED is blinking green, the projector does not accept any keypad and remote control input. When the lamp has cooled, the LED lights solid green and the fans slow down to minimal speed. To turn off the projector, toggle the power switch to the off position. NOTE: Once the projector has been toggled off, you must wait for one (1) minute before turning the projector on again. However, if the remote was used to power the projector to the Off state you do not need to wait one minute to turn it on again. blinking red see page 45 for more information solid red The following tables show common problems. When the problem is solved, you can skip the additional solutions. 22 Problem no start up screen Solution plug power cord in projector's left side remove lens cap toggle power switch toggle power switch on side Result correct image Start u Scre p en only start up screen appears press the Computer button activate laptop's external port Startu p Scree n computer image projected A A restart laptop A 23 Problem no computer image, just the words "Signal out of range" Solution press the Auto Image button on keypad Result computer image projected A Signa l rang out of e adjust computer refresh rate in Control Panel>Display>Settings>Advanced>Adapter (location varies by operating system) A A you may also need to set a different resolution on your computer, as shown in the following problem, "image fuzzy or cropped" 24 Problem image fuzzy or cropped Solution set your computer's display resolution to the native resolution of the projector (Start>Settings>Control Panel>Display>Settings tab) select 800x600 Result image clear and not cropped A A A A For a laptop, disable laptop monitor or turn-on dualdisplay mode move projector, adjust zoom, adjust height image not centered on screen correct image adjust horizontal or vertical position in Picture>Advanced menu 25 Problem image not square Solution adjust Keystone on keypad Result square image image not sharp adjust Sharpness (video sources only) in the Picture>Advanced menu correct image AB image does not fit 4:3 or 16:9 screen change aspect ratio to 4:3 or 16:9 in Picture>Aspect ratio menu correct image AB 26 Problem image upside down Solution turn off ceiling in Settings>System menu Result correct image image reversed left to right projected colors don't match source COLOR 27 AB turn off rear in Settings>System menu AB correct image A adjust color, tint, color temperature, brightness, contrast in the menus correct image AB COLOR Problem The video embedded in my PowerPoint presentation does not play on the screen Solution Turn off the internal LCD display on your laptop Result Embedded video plays correctly A B A B A B lamp won't turn on, LED blinking red make sure vents aren't blocked, turn off the projector and allow it to cool for one minute lamp turns on LED Start u Scre p en 28 Problem "Change lamp" message appears at startup or lamp won't turn on and LED blinking red Solution lamp must be replaced (see page 42) Result lamp turns on LED Start u Scre p en replace lamp 29 Using the remote control The remote uses two (2) provided AA batteries. They are easily installed by sliding the cover off the remote's back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover. Caution: When replacing the batteries, be aware that using batteries other than the type provided with the projector may risk severe damage to the remote. When disposing of the batteries, be sure to do so in an environmentally proper manner. To operate, point the remote at the projection screen or at the projector (not at the computer). Pressing the remote's Power button when the projector's Power toggle switch is in the Off position does not cause the projector to power up. You need to put the projector's Power toggle switch in the On position to let the remote power on the projector. When the projector is running, you can press the remote's Power button to place the projector in the Off state (see page 22 for shutdown info) and power it off. Press the remote's Menu button to open the projector's menu system. Use the arrow buttons to navigate, and the Select button to select features and adjust values in the menus. The remote also has Volume and Mute buttons to control the sound, and Video and Computer buttons to switch between sources. Use the Blank button to display a blank screen instead of the current slide (you can choose which color is displayed, see page 40); use the Effect button to invoke a user-definable action, such as freeze, or change your aspect ratio for viewing DVDs (see page 40 to learn to program this button). [. . . ] Twenty hours before the lamp life expires, the message "Change lamp" appears on the screen at startup. In this case, after replacing the lamp you must reset the lamp hours by simultaneously pressing both Volume buttons on the keypad and holding them for 10 seconds. Use only a replacement lamp with the same type and rating as the original lamp. Lamp hours used turn off and unplug projector wait 30 minutes 1 Turn off the projector and unplug the power cord. Using a flat-blade screwdriver, gently pry the lamp door from the projector by placing the screwdriver blade into the space between the top of the lamp door and the projector. lamp door 42 4 Loosen the two captive screws that attach the lamp housing to the projector. 5 Detach the lamp connector from the projector by depressing the locking tab on the connector and lightly pulling it free. [. . . ]