User manual ASCALADE WCP500

[. . . ] TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION GETTING STARTED Checklist of Parts Your Conference Telephone LCD Display on the POD Phone Key Basic Steps to Install Charging the POD To Ensure Better Performance BASIC OPERATIONS Standby Answering Calls Making Calls Traditional Dialing Predialing Redialing Traditional Dialing Predialing Phonebook Dialing Traditional Dialing Predialing Services Dialing Service Centre Quick Access Things you can do during a call Adjust Speaker Volume Mute Call Change Dial Tone Send Flash Signal Dialing Extra Digits Dialing from Phonebook Record Displaying User Phone Number Ringer Volume Adjusting Ringer Volume Ringer On/Off Shortcut Add New Number in Phonebook Programming Start Programming Ringer Melody 1 Owner's Manual B081 1. 8 GHz DECT Conference Telephone, Non-GAP, 1 Portable Part Flash Duration User Phone Number Network Services Number Service Centre Number Default Setting Additional Features Call Recording Out of Range Paging Low Battery WALL ­ MOUNTING QUICK REFERENCE GUIDE DEFAULT VALUE TROUBLE SHOOTING TECHNICAL DATA CONFORMANCE TO REGULATION 2 This telephone is not designed for making emergency telephone calls when the power fails. Make alternative arrangements for access to emergency services. IMPORTANT SAFETY INFORMATION Read the safety instructions before first use of this product. · · · · · · · · · · Read and understand all instructions. Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. [. . . ] Press CLEAR key to exit phonebook selection and to return to the call and talk timers. Pressing "* " , "#", PHONEBOOK, and SERVICE keys will have no effect. Press "UP" and "DOWN" keys to exit phonebook review and to adjust speaker volume. Press FLASH key to exit phonebook review and to send out flash signal. Press REDIAL key to exit phonebook review and to dial the last dialed number if it is available. vii. Exit from the phonebook selection after a while. · Press "0" ­ "9" to display the selected phonebook record. (After pressing the phonebook record number, the selected number will be dialed out accordingly. ) · Call timer and talk time remaining counter are displayed accordingly. · Press PHONE key again to end the call. 10 Phonebook Dialing Services Dialing Predialing · Press PHONEBOOK key. Services dialing allows you to call network service (eg. bridging services, long distance conference services) by a single key press. Refer to the programming section for how to enter or edit the services phone number. · The number will be displayed as it is dialed. · Press "0" ­ "9" to select the desired phonebook record. · The phone number cannot be edited. Note: If you do not want to make the call, pressing CLEAR key to exit phonebook selection and to return to Standby. · Call timer and talk time remaining counter are displayed accordingly. · Press PHONE key again to end the call. · Press PHONE key to seize the line and the number will be dialed out. · Call timer and talk time remaining counter are displayed accordingly. · Press PHONE key again to end the call. Note: If the network services number is not entered or modified and contains no digit, you will hear a reject tone and no call will be dialed. Note: If the service number has more than 18 digits, only the last 18 digits shall be displayed. The Scroll icon shall turn on. Note: If the phonebook number has more than 18 digits, only the last 18 digits shall be displayed. It can hold up to 44 digits in each phonebook number. 11 Service Centre Quick Access Things you can do during a call The Service Centre quick access allows you to call the service centre (eg. Refer to the programming section for how to enter or edit the service centre phone number. · The number will be displayed as it is dialed. You can do the following during a call, a. Display user phone number. Adjust Speaker Volume 16 different levels of speaker volume can be selected. · Press UP/DOWN key to adjust the speaker volume during the call. · Call timer and talk time remaining counter are displayed accordingly. [. . . ] · Press "5" to select network services number programming. (The LCD displays the current number if available; otherwise a blank screen will be displayed. ) · Press PROGRAM key to select service number programming. (The current number flashes. ) · Press CLEAR key to erase the digit of the current number one by one. · Press CLEAR key to exit. 17 Programming Programming Service Centre Number · Press and hold PROGRAM key during Standby. [. . . ]