User manual ARRI WIRELESS REMOTE SYSTEM SYSTEM GUIDE 2006

[. . . ] W R S _ WIRELESS REMOTE SYSTEM SYSTEM GUIDE 04/2006 02 04/2006 W R S _ System Guide 03 DEAR FRIENDS Working on a film set is a hectic business, and the equipment must meet high standards so you can perform your job as efficiently as possible. In designing this new generation of components for the Wireless Remote System we have carefully looked at the needs of the assistants and talked to many of you about existing lens and camera remote systems. As a result these new components are substantially smaller and lighter than before, while at the same time having longer battery life and a more robust radio transmission. No shoot is like the other, and a fast Steadicam chase requires a different wireless setup than a camera on a crane for a music video with speed ramps. [. . . ] To use the LDD-FP on the WMU-3, compatible software is required for the LDD-FP, Studio Lens Data Box LDB-2, Lite Lens Data Box LDB-2. The LDD-FP is not compatible with WMU-1, WMU-2, WHA-1, WHA-2 or WHA-3. It is not possible to operate the WRC-1 and the Lens Data Display for Focus Puller (LDD-FP) on the same Wireless Main Unit. For wireless operation of WRC-1 and LDD-FP at the same time, two Wireless Main Units must be used. K2. 54163. 0 Lens Data Display for the Focus Puller Lens Data Display for Focus Puller (LDD-FP) 16 W R S _ System Guide 04/2006 WRS COMPONENTS Wireless Extension Unit 1 (WEU-1) With this unit it is possible to connect the hand controllers to a Wireless Main Unit with a cable. It consists of the Wireless Main Attachment WMA-1, which mounts on the WMU, and the Wired Handgrip Attachment WHA-1, which accepts the hand controllers. The Wired Handgrip Attachment 1 can be used separately to connect the WRC-1 with cable WC-W1 to all models of ARRIFLEX 416 Plus, 235, 435, 535 or 16 SR 3. Compatibility: When the WHA-1 is used to connect the WRC-1 to the CCU port of a 435 Xtreme, fast ramps and the minimum speed of 0. 1fps are not accessible. The WHA-2 must be connected to the LCS port to access these features. Wireless Extension Unit 1 (WEU-1) K2. 52056. 0 Wireless Extension Unit 1 Wired Handgrip Attachment 1 (WHA-1) This handgrip attachment can be used to connect the Wireless Remote Control (WRC1) with cable WC-W1 to all models of ARRIFLEX 416 Plus, 235, 435, 535 or 16 SR 3. Compatibility: When the WHA-1 is used to connect the WRC-1 to the CCU port of a 435 Xtreme, fast ramps and the minimum speed of 0. 1fps are not accessible. K2. 52070. 0 Wired Handgrip Attachment 1 Wired Handgrip Attachment 1 (WHA-1) Wired Handgrip Attachment 2 (WHA-2) With this handgrip attachment the hand controllers WFU-1, WFU-3 and/or WZU-1, WZU-3 or the Wireless Remote Control (WRC-1) can be operated hardwired. Compatibility: The WHA-2 works with the ARRICAM Studio, the ARRICAM Lite, the ARRIFLEX 416 Plus and 435 Xtreme. It can be connected to the LCS socket of an ARRICAM Lens Data Box, 416 Plus, 435 Xtreme or to a UMC-3 with cable LC-M1, LC-M2, LC-Z1 or LC-Z2. Alternatively it can be connected to the CAC connector of Studio or Lite using cable KC-70 (3m/9ft). The Lens Data Display for Focus Puller (LDD-FP) cannot be attached to the WHA-2. The WHA-2 can be mounted on the camera with the Rod Bracket or with the Rosette Bracket. Wired Handgrip Attachment 2 (WHA-2) K2. 54079. 0 Wired Handgrip Attachment 2 04/2006 W R S _ System Guide 17 WRS COMPONENTS Wired Handgrip Attachment 3 (WHA-3) The WHA-3, just like the WHA-2, allows all hand controllers except the LDD-FP to be connected with a cable to an ARRICAM, 435 Xtreme or to a UMC-3. In addition the WHA-3 has a button on the left side for focus tracking. Focus tracking based on measured distances is available when using an ARRICAM, 435 Xtreme , 416 Plus or to a UMC-3 with the Lens Data Display for Focus Puller (LDD-FP) and a compatible distance measuring device (currently the Cinematography Electronics Cine Tape Measure). Compatibility: The WHA-3 works with the ARRICAM Studio, the ARRICAM Lite, the ARRIFLEX 416 Plus and 435 Xtreme. It can be connected to the LCS socket of an ARRICAM Lens Data Box, 416 Plus, 435 Xtreme or to a UMC-3 with cable LC-M1, LC-M2, LC-Z1 or LC-Z2. Alternatively it can be connected to the CAC connector of Studio or Lite using cable KC-70 (3m/9ft). The Lens Data Display for Focus Puller (LDD-FP) cannot be attached to the WHA-3. [. . . ] # K2. 52048. 0 K2. 54014. 0 K2. 54025. 0 K2. 52237. 0 K2. 52262. 0 K2. 54194. 0 K2. 54195. 0 K2. 52040. 0 435 Advanced, URM-1, 435 Xtreme, URM-2, URM-3, WHA-1, WHA-2, WHA-3 K2. 52226. 0 WMU-2, WMU-3 K2. 65000. 0 Camera Radios & Motor Controllers Accessories Unit Description Studio LDB Adapter Quick Change Adapter 3/8" Compatible with. . . . ARRICAM Studio, Studio LDB, Studio LDB-2 UMC-1, all models of ARRIFLEX 416, 235, 435, 535, 16 SR 3 Ident. # K2. 54144. 0 K2. 52080. 0 Camera Radios & Motor Controllers Accessories Unit CLM-1 CLM-2 Description Controlled Lens Motor 1 Controlled Lens Motor 2 Compatible with. . . . UMC-3, UMC-1, Studio LDB, Studio LDB-2, Lite LDB, Lite LDB-2, FEM-2 UMC-3, UMC-1, Studio LDB, Studio LDB-2, Lite LDB, Lite LDB-2, FEM-2 Ident. [. . . ]