User manual ARISTO AM-962

[. . . ] 3 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CPU Speed Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 JP52, JP55 - Host Bus Speed Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To prevent damage caused by static electricity, discharge the static electricity from your body before you touch any of the computers electronic components. Technical Reference Booklet 5 Motherboard Layout (Model Code No. - 35C96200XX) The following diagrams show the relative positions of the jumpers, connectors, major components and memory banks on the motherboard. NOTE 1) 2) Be sure to check the cable orientation in order to match the colored strip to the pin 1 end of the connector. When you start up the system, please wait for 5 seconds after you power on AC. Hardware Configuration 6 Jumper Settings This chapter explains how to configure the motherboard's hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. Refer to this chapter whenever in doubt. 1 JP41 JP8 1 CPU Speed Selection In this motherboard, jumperless feature is implemented such that no jumper is required to be set for different type of CPU installed. Celeron PGA370 CPU is frequency multiplier locked, no CPU speed change will be seen even if the frequency multiplier setting in CMOS setup is changed. JP52, JP55 - Host Bus Speed Select JP52 1 1 1 Open Open Close* JP4 - CMOS Clear JP4 1-2* 2-3 Selection Normal* CMOS Clear JP3 - IOQ Depth Setting JP3 1 1 Open* Close JP41 - AMR Setting JP41 1-2 2-3* Selection Primary Secondary* Technical Reference Booklet 1 JP55 JP52 JP4 2 1 1 JP7 JP55 1 1 JP3 Open 1-2 1-2* Host Bus Speed Select 133MHz 100MHz Auto* Selection Depth of 4* Depth of 1 Close Open * = Default setting. 7 JP7 - Ratio of Processor Core to System Bus Frequency Ratio 3 3. 5 4* 4. 5 JP7 2 1 2 1 2 1 2 1 Ratio 5 5. 5 JP7 2 1 2 1 2 1 2 1 Ratio 7 7. 5 8 -- JP7 2 1 2 1 2 1 * 6 6. 5 JP8 - Default Setting by Factory Pin Assignment Interinal Audio Connector CN25 : AUX-IN Pin 1 2 3 4 Pin 1 2 3 4 Assignment AUX-L GND GND AUX-R Assignment CD-L GND GND CD-R CN31 : CD-IN Pin 1 2 3 4 Pin 1 2 3 4 Assignment CD-R GND CD-L GND Assignment GND CD-L GND CD-R 1 RGLG CN24 : CD-IN 1 CN32 : CD-IN GLGR CN11 FRONT RANEL HEADER HEADER 2x12 PWR+ GND PWRLED+ PWRLEDHDDLED+ HDDLEDRST+ GND SPEAK GND VCC 1 3 5 7 9 11 13 15 17 19 21 23 +PWR - SW +PWR - LED +HDD - LED +RST - SW S NC + SUS+ SW RX TX + + NC S IrDA 2 4 6 8 10 12 14 16 18 20 22 24 SUS+ GND IRRX GND IRTX VCC KEYLOCK+ X X GND KEYLOCKGND X SPKER KEYLOCK Close Open * = Default setting. Hardware Configuration 8 Hardware Setup To Install DIMMs 1. Make sure the clips at either end of the socket are pushed away from the socket. Align the two small notches in the bottom edge of the DIMM with the keys in the socket. When the DIMM is seated, push down on the top edge of the DIMM until the retaining clips at the ends of the socket snap into place. If you installed a DIMM with ECC memory, start the computer and use the ECC Configuration feature in Setup to enable the use of ECC. Turn system power off before installing and removing any device, otherwise you'll cause the system damage. Technical Reference Booklet 9 Installing a New Processor An upgrade processor can dramatically increase general system speed and performance. Most microprocessor upgrade kits include the following items: · Microprocessor chip · Installation instructions and technical data Your system may have these features built in, or support them as upgrades. To Install a Processor to ZIF Socket To install the processor, follow these steps: 1. If the system microprocessor is already on the motherboard socket, you need to remove it from the motherboard socket. The socket is a Zero Insertion Force (ZIF) socket which has a metal arm at one side. Carefully grasp this arm, move it horizontally away from the socket and lift it up. Eventually you will be able to lift the chip straight up out of the socket. Be careful not to bend any of the pins when removing the microprocessor chip from its socket. Carefully align the processor with the correct orientation to the socket on the motherboard. To exit the Help Window press <Esc> or the F1 key again. In Case of Problems If, after making and saving system changes with the Setup Program, you discover that your computer does not reset, use the Award BIOS defaults to override the CMOS settings. Technical Reference Booklet 11 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from various setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu. CMOS Setup Utility - Copyright (C) 1984-1999 Award Software 8 8 8 8 8 8 8 Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status 8 Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving éêèç : Select Item Time, Date, Hard Disk Type . . . (Note : The figures of BIOS Setup Menu included here only show a typical case, and may not be exactly the same as the one on your unit. ) Note that a brief description of each highlighted item will appear at the bottom of the screen. Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PNP/PCI Configurations PC Health Status This setup page includes all the items of AwardTM special standard features. [. . . ] If the Security Option is set to "System", the password will be required both at resetting and at entering setup. If the option is set to "Setup", the prompt only appears when you try to enter setup. BIOS Setup 16 Flash Update Procedure A program AWDFLASH. EXE is included in the utility diskette or CD. The user is recommended to follow the procedure below to update the flash BIOS. Copy the new BIOS file (just obtained or downloaded) and the utility program AWDFLASH. EXE to the diskette. [. . . ]