User manual ARISTO AM-947

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Support Wake on Lan. Expansion Slots · · · 3 PCI bus master slots (rev. 1 AMR (Audio Modem Riser). CAUTION Static electricity can harm delicate components of the motherboard. To prevent damage caused by static electricity, discharge the static electricity from your body before you touch any of the computers electronic components. Technical Reference Booklet 5 Motherboard Layout (Model Code No. - 35894700XX) The following diagram shows the relative positions of the jumpers, connectors, major components and memory banks on the motherboard. AM R Slot C N 25 CN 22 JP41 J P 31 NOTE 1) Be sure to check the cable orientation in order to match the colored strip to the pin 1 end of the connector. Hardware Configuration 6 Technical Reference Booklet 7 Hardware Configuration 8 Technical Reference Booklet 9 Hardware Configuration 10 Pin Assignment 1. USB-VCC USB DT2USB DT2+ USB-GND CN9: USB Connector 1 7 1 3 5 7 USB-VCC USB DT0USB DT0+ USB-GND 2 8 2 4 6 8 4. CN23: CD-IN 1 1 5 4 4 USB-GND USB DT1+ USB DT1USB-VCC 5. CN25:AUX-IN 1 2 8 2 4 6 8 USB-GND USB DT3+ USB DT3USB-VCC 3. CN8: PS/2 Mouse Connector 1 2 3 4 5 VCC NC MS_DATA GND MS_CLK 1 2 3 4 GND CD-L GND CD-R 1 2 3 4 AUX_L GND GND AUX_R Warning: Power on after Power-Fail This new feature is enabled in this system, i. e. once plugging-in the AC-power, the system will start-up automatically. Please install all the components/devices into the system before plugging in the AC-power plug. Technical Reference Booklet 11 Hardware Setup The memory combinations. The motherboard will support Extended Data Output (EDO), Burst Extended Data Output (BEDO) and Synchronous DRAM (SDRAM) DIMMs. DIMM Configurations DIMM 1 Empty Empty Empty Empty Empty 8MB 8MB 8MB 8MB 8MB 8MB 16MB 16MB 16MB 16MB 16MB 16MB DIMM 2 8MB 16MB 32MB 64MB 128MB Empty 8MB 16MB 32MB 64MB 128MB Empty 8MB 16MB 32MB 64MB 128MB Total 8MB 16MB 32MB 64MB 128MB 8MB 16MB 24MB 40MB 72MB 136MB 16MB 24MB 32MB 48MB 80MB 144MB DIMM 1 32MB 32MB 32MB 32MB 32MB 32MB 64MB 64MB 64MB 64MB 64MB 64MB 128MB 128MB 128MB 128MB 128MB 128MB DIMM 2 Empty 8MB 16MB 32MB 64MB 128MB Empty 8MB 16MB 32MB 64MB 128MB Empty 8MB 16MB 32MB 64MB 128MB Total 32MB 40MB 48MB 64MB 96MB 160MB 64MB 72MB 80MB 96MB 128MB 192MB 128MB 136MB 144MB 160MB 192MB 256MB To Install DIMMs 1. Make sure the clips at either end of the socket are pushed away from the socket. Align the two small notches in the bottom edge of the DIMM with the keys in the socket. When the DIMM is seated, push down on the top edge of the DIMM until the retaining clips at the ends of the socket snap into place. Turn system power off before installing and removing any device, otherwise you'll cause the system damage. Hardware Setup 12 Installing a New Processor An upgrade processor can dramatically increase general system speed and performance. Most microprocessor upgrade kits include the following items: · Microprocessor chip · Installation instructions and technical data Your system may have these features built in, or support them as upgrades. To Install a Processor to ZIF Socket To install the processor, follow these steps: 1. If the system microprocessor is already on the motherboard socket, you need to remove it from the motherboard socket. The socket is a Zero Insertion Force (ZIF) socket which has a metal arm at one side. Carefully grasp this arm, move it horizontally away from the socket and lift it up. Eventually you will be able to lift the chip straight up out of the socket. Be careful not to bend any of the pins when removing the microprocessor chip from its socket. Carefully align the processor with the correct orientation to the socket on the motherboard. The Main Menu allows you to select from various setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu. STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNP/PCI CONFIGURATION LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS Esc : Quit F10 : Save & Exit Setup Time. Hard Disk Type (Note : The figures of BIOS Setup Menu included here only show a typical case, and may not be exactly the same as the one on your unit. ) Note that a brief description of each highlighted item will appear at the bottom of the screen. [. . . ] User Password : You can enter the Setup Program but cannot change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD: Type the password, up to eight characters in length, and press<Enter>. The new password will clear the previously entered password from the CMOS memory. You may also press <Esc> to abort the selection and operate without a password. [. . . ]