User manual ARCAM SOLO NEO

[. . . ] Handbook safety guidelines CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Warning Mains plug/appliance coupler is used to disconnect device and it shall remain readily operable. CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. CAUTION: To reduce the risk of electric shock, do not remove cover (or back). [. . . ] Solo Neo provides: < up to 30 station presets; < full RDS information on FM (where transmitted); programme-associated data on DAB; < FM signal-strength and DAB data-rate meters. Source selection Preset mode indicator Switching to the radio Press SOuRCe+ or SOuRCe- until the radio type that you wish to listen to (DAB/FM) is displayed on the front panel. Alternatively, press the DAB or FM button on the remote control for direct access. Transmission details, or other information Searching for stations Pressing the MODe button when the radio is selected as the music source toggles between the two tuning modes of Solo Neo ­ `Preset' or `Tune'. When in preset mode, pressing the B or C buttons on the remote control (0 or / on the front panel) shows the previous/next station preset (if these are defined). Note that these buttons have no effect, in preset mode, if no presets are defined. In tune mode, by contrast, pressing these buttons changes the FM tuning frequency or selects the next DAB radio station from the station list. FM To search for new stations, ensure that Solo Neo is in `Tune' mode, as described above. Use the B and C buttons (0 or / on the front panel) to select the desired tuning frequency. It is also useful if you are trying to select a station that is too weak for automatic tuning. Pressing the B or C buttons on the remote control (0 or / on the front panel) for longer than one second engages automatic tuning. Solo Neo searches for a radio station signal of sufficient strength, then stops. To skip to the next station, press one of the buttons again. DAB Tuning stations in under DAB is different from conventional FM tuning, in that you do not need to know the transmission frequency of the station ­ this is handled for you by Solo Neo. Navigate through the menu options (see page 16) until `DAB Setup' is displayed. There are two options under this menu item ­ `Scan' and `Erase settings'. If any are found, then they will be added automatically to the list of available stations. To select a DAB radio station, press the B or C buttons on the remote control until the name of the station you want to listen to is displayed. If O is not pressed, the display will return to the current station after a few seconds. Display modes Solo Neo provides different display modes when listening to the radio. The mode is changed (cycled) by pressing the INFO button on either the front-panel or the remote-control. Programme type (DAB/FM): a short description of the type of programme being transmitted. Transmission frequency (FM): the station name (if available) and transmission frequency. Dynamic label (DAB)/ RDS (FM): 128 characters of text used by broadcasters to give programmerelated information (e. g. , `phone numbers, webaddresses, etc. ). Data rate (DAB): this mode shows the data-rate of the station (in kbits/s) and the transmission mode. A higher data-rate indicates a higher audio quality, with the maximum rate being 256kbits/s. [. . . ] IP Address; security passphrase) Select digit to change O. Enter key: >OO Increment/Decrement digit (number or letter) Save setting Primary DNS O. O Enter key: >1OAF35D6A8D5693 Note: When all settings have been adjusted according to the needs of your network, the settings must be applied by navigating to the `Apply Settings' screen and pressing An example key (password) is shown. Enter your own network key. Apply Settings Press OK to accept E19 NET Radio Connecting. . . English Network Run Setup Wizard technical specification Pre-amplifier Inputs Maximum input level Input impedance Signal/noise ratio Co-axial outputs Maximum output level Output impedance Optical output (TOSLINK) Sample rate 44. 1kHz (with CD playback), 48kHz (with DAB, FM, NET & USB receiver), otherwise muted. 2. 5Vrms 500 2. 5Vrms 47k 105dB General Supply voltage* Power consumption Size (W x D x H) Weight (net) Weight (packed) Supplied accessories 100V, 115V or 230V AC, depending on shipping region Standby 1W; Operational 25W (typical), 400W (maximum) W430mm x D350mm x H79mm 7. 75kg 10. 5kg Mains lead Wire dipole aerial (Band III) Wi-Fi antenna Remote control handset and two AAA batteries Instruction manual and registration card * This is a Class 1 device and must be earthed. Amplifier Continuous power output, per channel, 80khz measurement bandwidth Both channels, 4, 1kHz Distortion, both channels 4, 80% power, 1kHz 75Wrms, 0. 013% THD+n 0. 011% THD+n Radio interference Solo Neo is an audio device containing microprocessors and other digital electronics. [. . . ]