User manual ARCAM SOLO MOVIE 2.1

[. . . ] Handbook Manuel Handbuch Handleiding so mo l v ie 2. 1 o safety guidelines CAUTION:To reduce the risk of electric shock, do not remove cover (or back). WARNING:To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated `dangerous voltage' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. [. . . ] If your music is not `warm' enough, increase this setting; if your music is `boomy', decreasing this setting may help. Treble This setting changes the relative volume of the higher frequency components of your music. If you feel that percussion items in the music (for example) are being lost, increasing this setting may help. Bass correction may be used if Solo Movie 2. 1 is connected to limited-frequency-range (`Small') speakers, that cannot reproduce very low frequency sounds. Increasing this setting progressively increases very low frequency bass. This control should not be used at high volumes as it may damage your speakers. Sub Level * This adjusts the level of the SuB (subwoofer, or LFE speaker) pre-amp output relative to the other two channels. Sleep Timer This timer allows you to specify a listening period, after which Solo Movie 2. 1 will switch automatically into stand-by. The period can be set in 5-minute intervals, up to 120 minutes (2 hours). FM Mode (This menu item is shown only when the selected source is FM. ) In some weak signal areas, it can be beneficial to force the FM tuner to mono output, as mono requires a much lower signal strength to produce acceptable results. If the signal strength in your area is good, leave this as `stereo'. DAB Setup (This menu item is shown only when the selected source is DAB. ) There are two options under this menu item ­ `Scan' and `Erase settings'. Selecting `Scan' causes Solo Movie 2. 1 to search for new DAB stations. If any are found, then they will be added automatically to the list of available stations. Scanning for new stations does not erase old stations that are no longer transmitted ­ over time, or if you change location, this may lead to you having a number of stations in your list that cannot actually be received. In this case, select `Erase settings', then perform a new scan; when the scan is complete, only stations that are available currently in your area will be shown. Set Preset (This menu item is shown only when the selected source is DAB, FM or AM. ) This allows you to store a radio station that you have tuned in to as a numbered preset (confirm with oK). The station can then be retrieved by pressing the preset number on the remote. In the same way, you can erase a particular numbered preset (confirm with oK). See the section `Setting station presets' on page 25 for more information. iPod Option (This menu item is shown only when the selected source is AUX. ) The default setting is `Disabled', but if you intend to use Arcam's rDock or rLead accessories to integrate an iPod® with your system, you should set the appropriate option. Connect the rDock or rLead to the rear of the unit (full details are given in the quick start guides supplied with the accessory units) and Solo Movie 2. 1 will test for the presence of a connected iPod. [. . . ] Please contact your dealer for further information. Problems with audio The type of audio provided by the HDMI connector depends on the configuration of Solo Movie 2. 1 (see `Audio Setup' on page 19). Note that pure DVI devices (connections requiring a HDMI to DVI convertor cable) do not support audio via this connection. Note that for audio to be transmitted over HDMI, `Digital audio out' must be set to `HDMI'. CD-R/RW and DVD-R/RW compatibility < < < < < < < < This unit will play CD-R and CD-RW discs recorded in CD Audio or Video CD/Super VCD format, or as a CD-ROM containing the audio and video file types listed above. Other content may cause the disc not to play, or to create noise/ distortion in the output. [. . . ]