User manual ARCAM FMJ T32

[. . . ] T32 HANDBOOK Radio tuner English Warning Mains plug/appliance coupler is used to disconnect device and it shall remain readily operable. safety guidelines CAUTION: To reduce the risk of electric shock, do not remove cover (or back). WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated `dangerous voltage' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. [. . . ] In either of these cases you should have sockets in your home marked fM or Vhf (do not use those marked TV); these should be connected to the fM coaxial connector on the rear of the unit. Sirius An antenna suitable for receiving Sirius satellite broadcasts is included with the SiriusConnectTM Home Tuner accessory (not supplied). The Sirius 8-pin connection cable lets you control the tuner through your Arcam T32. Plug in the tuner module, set up the indoor/outdoor satellite radio antenna and activate your SIRIUS subscription before use (see page 12). Visit www. sirius. com for more information. AM An AM aerial is required to receive AM/medium wave radio signals, so a simple loop aerial is supplied. Make sure that the aerial is positioned well away from TVs, computers and other sources of RF noise. Rotate the aerial to discover which position gives the best reception. In weak signal areas, or when the T32 is in use inside a steel-framed building (such as an apartment building), a wire between 3 and 5 metres long can be used to improve reception. Mount this high up outside the building if possible, and connect one end of this wire to the aM Loop connector, in addition to the loop aerial supplied (i. e. do not disconnect the AM loop aerial). Assembling the AM loop aerial 1. Release the tie-wrap and unwind the twisted lead. Fold the plastic stand forward through the loop frame. Information on radio transmissions In the UK, the following Internet resources may be of interest: www. bbc. co. uk/reception/info/index. shtml This gives access to downloadable factsheets in PDF format on DAB digital audio, Analogue radio (FM/AM), Radio recption on the move and RDS, and Radio reception overseas. www. bbc. co. uk/radio/waystolisten/analogue To find the optimum frequencies for listening to BBC national radio networks in your area. www. frequencyfinder. org. uk This gives a comprehensive station directory for the UK and Ireland, in frequency order, or by selecting a town or city. www. mediauk. com/radio This gives detailed information on all UK radio stations, including contact details, transmission frequencies and channel numbers. Where Sirius satellite radio broadcasts are available, see: www. sirius. com/whatsonsirius This gives programme details of Sirius satellite radio, a subscriber service available throughout most of North America. Information about their 130 channels of commercial-free Music, Sports, News and Entertainment programmes is available from the Sirius. com home page. 2. Push the tab into the open slot in the base of the stand. Press until the tab clicks home. 3. Connect the lead wires to the AM socket at the rear of the unit (the wires are not polarised). Rotate the aerial's stand until you obtain the best reception. E-9 English operation Front panel operation These functions can also be controlled by the CR90 remote control. (See pages 14 for details. ) OK Press oK to confirm a digital radio channel selection or a preset selection. (Equivalent to O on remote control. ) STANDBY Press sTandby to switch the tuner between On (green light) and Standby (red light). (Equivalent to P on remote control. ) Control knob Used to manually tune stations by selecting a frequency, or to cycle through stations (DAB, Sirius) or stored presets. Also used to select settings within a setup menu item. DISP Press disp to cycle through the brightness settings of the front-panel display. (Equivalent to D on remote control. ) Preset buttons (1­8, 2­9, etc. ) Press a Preset button briefly to select the first preset number listed (Preset 1, for example). [. . . ] Set `Repeat mode' by pressing R on the remote. Selecting a preset To select a stored preset: < Press one of the dedicated front panel preset buttons briefly (for presets 1 to 7). < Use the numeric keypad on the remote control to enter the preset number. < Press pReseT on the front panel (or p/Tune on the remote) and use the control knob (or D and E on the remote control) to select a used preset from 1 to 100. < Press C or B to select a used preset from 1 to 100. Music Make Selection è Navigate through the different ways of selecting tracks on your iPod (the actual categories will depend on your iPod model) by pressing C and B on the remote, confirming your selection with O. è Preset 05 FM 98. 50MHz Press O on the remote control or oK on the front panel within the time-out period to output the selected station. E-13 The CR90 Universal remote controller Select the source key first Remember to select a source key before pressing command buttons ­ commands vary depending on the source selected! [. . . ]