User manual ARCAM DV29

[. . . ] Arcam DV29 DVD player Lecteur de DVD Arcam DV29 DVD-Spieler Arcam DV29 Arcam DV29 DVD-speler Safety guidelines CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: To reduce the risk of electric shock, do not remove cover (or back). WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated `dangerous voltage' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. [. . . ] We recommend `Centre Width' is set to 3 for normal use. Panorama Mode (This setting can be adjusted only when Dolby Pro Logic II Music mode is selected. ) Extends the front centre image to include the surround speakers for an exciting `wrap-around' effect with side wall imaging. The `Centre Width' setting for Dolby Pro Logic II Music Mode DV29 E-16 Speaker set-up This menu screen allows you to specify the speaker configuration that is connected either to the analogue ouputs of your DVD player, or to your HDMI receiver when the HDMI link is carrying multi-channel uncompressed audio. (If you are using the coaxial or optical audio outputs, set all speakers to `Large' or `Present'. ) It is important that this configuration reflects accurately the actual situation, otherwise audio quality may be severely compromised. The speakers are indicated as follows: Front L/R Centre Surround L/R Subwoofer This is the setting for the `Front' speakers (the speakers used for 2channel stereo output). This is the setting for the `Surround' speakers (normally next-to or behind the user). For each speaker, the player can be configured to send either audio with the full frequency range of the source material, or with a reduced frequency range. The reduced frequency range option is used normally when `satellite' speakers are used for the surround channels; these cannot handle low frequency information. Full frequency speakers are commonly called `Large' speakers, with reduced-range speakers given the name `Small'. Low frequency information is rerouted from `small' speakers to `large' speakers, or to the subwoofer (depending on the speaker configuration). Any speaker that is not connected should be identified by selecting `Not Present' for that speaker. Although the DV29 is very flexible in the speaker configurations it can handle, some restrictions have been applied. For example, if no subwoofer is present, then it is not possible to configure the Front speakers to be `Small' since there would be nowhere to redirect the low frequency information. No sound from the centre/rear speakers?Ensure that the following are correct: n A multi-channel source is being played; n The `Audio' item is set to `Bitstream/6 Ch. '; n The connection Stereo+Sub This setting is relevant to 2-channel source material only (such as CDs). It controls whether the low frequency information is redirected to the subwoofer, or not. This item can be changed only if a subwoofer is specified as present in the system. None Crossover Duplicate No redirection of low-frequency information occurs; all the audio is sent to the Front speakers. Low-frequency information is redirected to the subwoofer, with the remaining (higher-frequency) information sent to the Front speakers. In addition, the low-frequency information is duplicated to the subwoofer. between the DV29 and your audio device is made correctly ­ if using multichannel analogue output, check that the cables have not been swapped. Crossover Frequency This setting defines the frequency at which bass redirection begins. Frequencies below this level are redirected from `small' speakers to the Fronts or to the subwoofer; frequencies above this level are not redirected. The redirection frequency is the same for all the speakers in a system. The optimum crossover frequency depends on the characteristics of your speaker set-up, and is best determined by experimentation. We suggest you start at 100Hz. Delay set-up The delay set-up menu page allows two different type of delay to be configured: those due to speaker positioning and those due to video post-processing. Speaker positioning The relative positioning of speakers within a room (particularly a large room) may mean that sound from some speakers arrives at the listener later than sound from others. By altering the delay settings for the different speakers, this difference in arrival time can be reduced or eliminated. When setting the delay, it should be imagined that the listener is sitting in a circle of the speakers; the delay indicates the distance of the speaker from the listener. Measurement Units Your DV29 allows you to choose the measurement units that you feel most comfortable with: metres or feet. Delays Delays for the front, centre and surround speakers can be set using the associated sliders. [. . . ] Permet de modifier la sélection d'angle pour un disque DVD. Angle codes: Code: `1' (0x31) `2' (0x32) `3' (0x33) `4' (0x34) `5' (0x35) Angle: 1 2 3 4 5 Code: `6' (0x36) `7' (0x37) `8' (0x38) `9' (0x39) Angle: 6 7 8 9 P2 COMMAND: Byte: CC P1 Description: `G' (0x47) (Command code) Angle selection: `0' (0x30) ­ Previous angle `1' (0x31) ­ Next angle `Q' (0x51) ­ Request current angle information `~' (0x7E) ­ (Reserved) RESPONSE: Byte: RC AC Description: `G' (0x47) (Reply Code) Answer code Current angle (see below) Total angles (see below) `~' (0x7E) ­ (Reserved) Example / Exemple / Beispiel / Voorbeeld Command/response sequence to select the previous angle, where the new angle is number 6 and there are 7 angles in total: Séquence de commande/réponse pour sélectionner l'angle précédent, le nouvel angle étant le numéro 6, avec un total de sept angles : P1 P2 P3 Befehls-/Rückmeldesequenz zur Auswahl des vorherigen Winkels, wobei der neue Winkel Nr. 6 ist und es insgesamt sieben Winkel gibt: Opdracht- en responsreeks om de vorige hoek te selecteren, waarbij nummer 6 de nieuwe hoek is en er zijn in totaal 7 hoeken: COMMAND: !G0~ ­ followed by/suivie d'un/gefolgt von/gevolgd door (0xD) RESPONSE: !G@67~ ­ followed by/suivie d'un/gefolgt von/gevolgd door (0xD) Player menu / Menu du lecteur / Gerätemenü / Spelermenu Open/close a player menu. Een spelermenu openen/sluiten Example / Exemple / Beispiel / Voorbeeld Command/response sequence to select Bookmark menu open: Séquence de commande/réponse pour sélectionner l'ouverture du menu de signet Befehls-/Rückmeldesequenz zur Auswahl des Lesezeichenmenüs: Opdracht- en responsreeks om het menu Bookmark te openen: COMMAND: !H11 ­ followed by/suivie d'un/gefolgt von/gevolgd door (0xD) RESPONSE: !H@1~~ ­ followed by/suivie d'un/gefolgt von/gevolgd door (0xD) P2 COMMAND: Byte: CC P1 Description: `H' (0x48) (Command code) `0' (0x30) ­ Close menu `1' (0x31) ­ Open menu `2' (0x32) ­ Toggle menu state `Q' (0x51) ­ Request menu state `1' (0x31) ­ Bookmark menu `2' (0x32) ­ Search menu `3' (0x33) ­ Programme menu `4' (0x34) ­ Trim menu `5' (0x35) ­ Pro Logic II menu `6' (0x36) ­ Setup menu `~' (0x7E) ­ Used for request menu command RESPONSE: Byte: RC AC P1 Description: `H' (0x48) (Reply Code) Answer code `0' (0x30) ­ No menu open `1' (0x31) ­ Bookmark menu open `2' (0x32) ­ Search menu open `3' (0x33) ­ Programme menu open `4' (0x34) ­ Trim menu open `5' (0x35) ­ Pro Logic II menu open `6' (0x36) ­ Setup menu open `@' (0x40) ­ Unknown menu open P2 P3 `~' (0x7E) ­ (Reserved) `~' (0x7E) ­ (Reserved) DV29 E-39 E nglish Number / Nombre / Zahl / Nummer Send a number to the DVD player. [. . . ]