User manual ARCAM DIVA AVR350

[. . . ] H A N DBOOK AVR350 Arcam AVR350 surround sound receiver English Safety guidelines CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: To reduce the risk of electric shock, do not remove cover (or back). WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated `dangerous voltage' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. [. . . ] 1/STATUS Press this button to toggle between FM `stereo mute' and `mono' on the tuner. DIS (Display) Press to cycle through Off/Dim/Bright illumination of the front panel display TRM (Speaker trim) Press to display the OSD Speaker trim level menu. TRM allows temporary adjustment of speaker levels, using the navigation buttons. Press again to exit the `Speaker Trim' function. The other buttons in this area are used for DVD control and do not effect the AVR350. NOTE Remember to install the two AA batteries supplied before AVR350 trying to use your remote control. E-19 English For information on using the remote control for other devices, and a full list of features, see the instruction booklet supplied with the CR80. Operating your AVR350 For information display we recommend you use the OSD on your TV/screen whenever possible. However, all key information is also duplicated one line at a time on the front panel display of the AVR350. Switching on/off Press the POWER button in. After approximately two seconds, the power LED will turn green and the current input and volume level will be shown; after a further 10 seconds, the AVR350 is ready for use. Please wait until the unit has finished initialising before attempting to operate the AVR350. It is recommended that if the unit is switched off, you should wait at least 10 seconds before switching the unit back on. Stand-by The AVR350 has a stand-by mode which can be entered by pressing the green stand-by button on the remote control. When in stand-by mode the display is blank and the power LED glows red. If you do not wish to put Zone 2 into stand-by at the same time as the main zone, press and hold the stand-by button on the remote control for about 3 seconds. After this time, the front-panel of the AVR350 will display the text `Main Off', before going into stand-by; the LED for Zone 2 will be illuminated to show that Zone 2 is still operating. When not being used, the AVR350 may be left in stand-by mode, as power consumption is low. If you are not using your AVR350 for several days, however, we recommend you switch the unit off completely using the front panel power button. To switch on from stand-by, press one of the source buttons on the front panel or on the remote control, or use the stand-by button on the remote control. Volume control To adjust the volume level of the loudspeakers, pre-amp outputs and headphones use the volume control knob. Note that different sources may require different settings of the volume control to achieve the same perceived volume level. It is important to realise that the value indicated for the volume level is not an accurate indication of the power delivered to your loudspeakers. The AVR350 may deliver its full output power long before the volume control reaches its maximum position, particularly when listening to heavily recorded music. In comparison, some movie sountracks can appear to be very quiet, as many directors like to keep the maximum levels in reserve for special effect sequences. The volume can be controlled over a range of 100dB in 1dB steps. Muting the volume Pressing the MUTE button will mute the output of the AVR350 to the speakers and from the `pre-amp out' connectors (the output to the record loops remains unaffected). Press MUTE for a second time (or adjust the volume) to exit the mute state. Front panel display In normal operation, the display shows the current volume setting; smaller illuminated areas indicate the audio input type (digital or analogue) and the digital stream type (if applicable). If the processing mode changes (for example, from Dolby Pro Logic decoding to Dolby Digital 5. 1), then this will be displayed `in large letters' for about 2 seconds. Changing the display brightness (the DISPLAY button) It is possible to select the illumination level of the front panel display. Press DISPLAY on the front panel or DIS on the remote to cycle through the three illumination levels (Off/Dim/Bright). AVR350 E-20 Input selection To select a particular source, press the corresponding button on the front panel or on the remote control. There are eight inputs available: DVD, Sat, AV, PVR, VCR, Tape, CD and MCH (DVD-A multi-channel). [. . . ] n Een analoge/digitale geluidsingang voor de huidige bron selecteren. `1' (0x31) ­ Use the digital audio for the current source (if available). Increment/Decrement Preset / Augmentation/diminution de la présélection/ Erhöhen/Verringern der Voreinstellung/ De voorinstelling verhogen/verlagen g Increment/decrement the current tuner preset. The value returned for the new preset is offset by 0x30. To obtain the correct value, subtract 0x30 from the reported value. CoMManD: Byte: CC P1 P2 Description: `9' (0x39) (Command code) `~' (0x7e) (Reserved) `0' (0x30) ­ Decrement tuner preset `1' (0x31) ­ Increment tuner preset `9' (0x39) ­ Request the current preset number. reSPonSe: Byte: RC AC P1 P2 Description: `9' (0x39) (Reply Code) Answer code `~' (0x7e) (Reserved) Response: The preset number after the command has been processed, + `0' (0x30) < Formula: actual preset = (reported preset ­ 0x30) f Augmentation/diminution de la présélection actuelle du tuner. La valeur retransmise pour la nouvelle présélection est décalée de 0x30. Pour obtenir la valeur correcte, ôtez 0x30 de la valeur rapportée. < Formule : présélection réelle = (présélection rapportée + 0x30) d Erhöhen/Verringern der aktuellen Tuner-Voreinstellung. Der ausgegebene Wert für die neue Voreinstellung ist um 0x30 versetzt. [. . . ]