User manual ARCAM AVP700

[. . . ] H A N DBOOK/MANUEL/HANDBUCH / H A N D L E I D I N G AVP700 Arcam AVP700 Pre-amp. processor Préamplificateur-processor Arcam AVP700 Vorverstärker/Prozessor Arcam AVP700 Arcam AVP700 Voorversterker processor English Français Deutsch Nederlands Safety guidelines CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: To reduce the risk of electric shock, do not remove cover (or back). WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated `dangerous voltage' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] For example, to assign the Component/RGB video from the `HQ Video DVD' input to the DVD button, set the `HQ Video DVD' item in this menu to `DVD'. If HQ-VIDEO is set to RGB (as described on page 13) and an HQ-video input is assigned to a button, the AVP700 assumes that RGB signals are present for that input if a composite signal is found on the corresponding composite input. If this assignment is made but no RGB signals are supplied, the display will be blank for the assigned source. For HDMI video assignment, please see "ADV 6 ­ HDMI Settings". ADV 3 ­ Digital Settings Coaxial inputs and Optical inputs. Each of the digital inputs can be assigned to any of the seven stereo source buttons (CD, TAPE, DVD, SAT, AV, VCR and AUX), or can be assigned No button. This menu page lists the physical inputs, as per the back panel, on the left hand side of the screen, with the buttons used to select the inputs listed on the right hand side. For example, if you choose the `Coaxial DVD input' to be assigned to the DVD button, then the choices for the other digital inputs are: CD, TAPE, SAT, AV, VCR, AUX and NO BUTTON. If you wish to re-allocate the DVD input to a different button, `Coaxial DVD input' must be assigned to a different button (or No button) before you can re-assign the DVD input. AVP700 E-16 ADV 4 ­ Zone 2 Settings ZONE2 VOL: Sets the volume for Zone 2. Max Vol 20­83: Limits the maximum volume setting for Zone 2. This is a useful feature to prevent accidental over-driving of low power-handling speakers, for example. Fix Vol: This selects between fixed and variable audio output to Zone 2. If NO is selected, the output level can be controlled from Zone 2 or the main system. If you wish to fix the volume level, first set the Zone 2 volume to the desired level, then select Max On Vol: Limits the maximum volume Zone 2 operates at when it is first switched on. Zone 2 comes on at this volume if the last used volume exceeds this value. Stand-by: This allows zone 1 (the main zone) to be put into stand-by, either locally only or by Zone 2 as well. < < LOCAL ONLY: Only the main zone will be switched into stand-by from the main zone. ALL OFF: Both the main zone and Zone 2 will be switched into stand-by from the main zone. Access: This acts as a `parental control' device to disable or enable access to sources for Zone 2. Press the unwanted source button on the remote control handset or front panel to disable it for Zone 2. Enabled sources are listed on the `Access:' line of the menu page. ADV 5 ­ Analogue Settings Input trims: Allows the adjustment of the input sensitivity of the analogue inputs (in Volts RMS) so that each one achieves the optimum dynamic range and sounds similar in loudness to the others. Available level settings are: LOW 0. 5V, MEDIUM 1V, REFERENCE 2V, HIGH 4V. If a source is very quiet compared with the other sources you can increase its loudness by selecting the MEDIUM 1V or LOW 0. 5V settings. ADV 6 ­ HDMI Settings DVD and SAT: Allocate the HDMI inputs to any source buttons. For example, to assign the HDMI input labelled `DVD' to the VCR button, set the `Input: DVD' item in this menu to `VCR'. Saving Settings and Exit Set-up You can either save the settings now or exit without saving the changes. Press MENU to go to the `Set-up Menu Index' at the `Save Set-up' point. Press OK to select `Exit Set-up' and exit system configuration. Exit without saving If you choose to `Exit Set-up' without first saving the changes, then the new settings will be lost. Press MENU to go to the `Set-up Menu Index' at the `Save Set-up' point. [. . . ] So, for example, to program in a `Stand-by' command, use the command `16-124'. Zone 2 also uses RC-5 system code 16 as standard, as Zone 2 is normally operated in a separate room using a standard (system code 16) remote control. Items shown in THIS STYLE indicate the equivalent remote control button of the supplied CR-80 remote control. Command Stand-by On Zone 1 stand-by Power toggle Display (DIS) Menu (MENU) Info Command code 124 123 125 12 59 82 55 Command MODE Command code 32 106 107 108 109 102 110 111 112 103 104 105 Mono mode Stereo mode Dolby PLII Movie Dolby PLII Music (Reserved) Dolby PL Emulation DTS Neo:6 Cinema Mute Un-mute Mute toggle (MUTE) Volume up Volume down 119 120 13 16 17 DTS Neo:6 Music Dolby PLIIx Movie Dolby PLIIx Music (Reserved) Effect (FX) SAT input AV input TUNER input DVD input TAPE input VCR input AUX input CD input DVD-A input 70 63 64 65 66 67 68 69 0 2 3 4 5 6 8 7 9 Effect off Effect: Music Effect: Party Effect: Club Effect: Hall Effect: Sport Effect: Church Trim menu (TRM) Sub trim menu (SUB) 37 51 50 84 Stereo Direct on Stereo Direct off Stereo Direct toggle 78 79 10 Lip sync. [. . . ]