User manual APRILIA SCARABEO 250 I.E. 2006

[. . . ] In the text and figures the symbols 3 preceded by the symbol of the model (. 7!2. ). '3 02%#!54)/. 3 '%. %2!, !$6)#% Before starting the engine, carefully read this manual and in particular the section "SAFE DRIVE". Your and other people's safety depends not only on your quickness of reflexes and on your agility, but also on what you know about the vehicle, on its efficiency and on your knowledge of the basic information for "SAFE DRIVE". Therefore, get a thorough knowledge of the vehicle, in such a way as to be able to drive in the traffic safely. # manual, be careful to the potential risk of personal injury. [. . . ] Frame no. NOTE Do not alter the identification numbers if you do not want to incur severe penal and administrative sanctions. In particular, the alteration of the frame number results in the immediate invalidity of the guarantee. 48 use and maintenance Scarabeo 50 - Scarabeo 100 ENGINE NUMBER . The engine number is stamped near the lower support of the rear shock absorber. Engine no. ENGINE NUMBER / The engine number is stamped on the rear side, near the rear brake adjuster. Engine no. use and maintenance Scarabeo 50 - Scarabeo 100 49 !)2 #, %!. %2 . Carefully read p. Check the conditions of the air cleaner and clean it monthly or every 4000 km (2500 mi), depending on the conditions in which the vehicle is used. If the vehicle is used on dusty or wet roads, the cleaning operations and any replacement should be carried out more frequently. Before the cleaning operation, it is necessary to remove the air cleaner from the vehicle. REMOVAL N Position the vehicle on the centre stand on firm and level ground. N Withdraw the whole filter (4) by pulling it downwards. CLEANING THE AIR FILTER N Separate the grid (5) from the support (6). N Remove the filtering element (7). aWARNING Do not use petrol or inflammable solvents to wash the air cleaner, in order to avoid fires or explosions. N N To clean the filtering element use clean, non-inflammable solvents or solvents with high volatility point, then let it dry thoroughly. Apply a filter oil on the whole surface of the filtering element, then squeeze it to eliminate the oil in excess. NOTE The filter must be well impregnated, though not dripping. 50 use and maintenance Scarabeo 50 - Scarabeo 100 !)2 #, %!. %2 / Carefully read p. In this case consult your APRILIA Official Dealer, who will carry out the proper maintenance operation. N Place the support under the vehicle and a spongy cloth between them, so that the front wheel can move freely and the vehicle cannot fall down. aCAUTION Make sure that the vehicle is stable. N Put a support (1) under the tyre, in such a way as to keep the wheel in its position after loosening it. Wheel pin driving torque: 50 Nm (5 kgm). N N N Make the front wheel advance until you can withdraw the disc from the brake caliper (5). Without removing the brake caliper, rotate the left rod (6) clockwise, in such a way as to create the space necessary to withdraw the wheel. Disconnect the odometer control (7). 54 use and maintenance Scarabeo 50 - Scarabeo 100 REASSEMBLY Carefully read p. 45 (MAINTENANCE). aCAUTION While reassembling the wheel, be careful not to damage the brake pipe, the disc and the pads. To reassemble the front wheel, proceed as follows: N Spread a film of lubricating grease on the whole length of the wheel pin (2), see p. N Position the tang (8) of the odometer control (7) in the appropriate seat in the wheel hub. N aWARNING Danger of injury. Do not introduce your fingers to align the holes. N NOTE . Move the wheel until its central hole and the holes on the fork are aligned. The slot (10) in the brake caliper (5) must be located in the lug (11) on the inside of the left fork leg. Insert the wheel between the rods, carefully introducing the disc in the brake caliper. N Insert the washer (4) between the odometer control (7) and the fork right rod. N With pulled front brake lever, press the handlebar repeatedly, thrusting the fork downwards. Driving torque of the wheel pin clamp screw: 12 Nm (1. 2 kgm). N Make sure that the following components are not dirty: ­ tyre; ­ wheel; ­ brake discs. aCAUTION After reassembly, pull the front brake lever repeatedly and check the correct functioning of the braking system. [. . . ] 180 kPa (1. 8 bar) Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 kPa (2. 2 bar) INFLATION PRESSURE WITH PASSENGER (where drive with passenger is allowed) Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 kPa (2. 0 bar) Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 kPa (2. 5 bar) 84 use and maintenance Scarabeo 50 - Scarabeo 100 IGNITION Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]