User manual APRILIA ELECTRONIC ALARM 2007-2008

[. . . ] Should you lose or misplace your CODE CARD, you will have to have a complete new alarm system fitted. INITIAL START-UP Every time your vehicle's battery is disconnected, you will have to re-enable the alarm system by turning the ignition key (off-on-off). THE FEATURES OF THE REMOTE CONTROL Button A: used for arming and disarming the alarm system and for doing the procedures needed to customise the alarm functions. Led on the Remote Control: this will light up every time button A or button B is pressed. [. . . ] The alarm will continue providing this information until you turn the ignition key or arm the alarm system again. You can alter its settings to meet your particular needs by following the procedure below: 1) Arm the system using the remote control. Every time you press the button you should see the direction indicators flash. After you have pressed the remote control button for the fourth time, the alarm system will emit four flat sounds (boops) confirming it has entered programming mode. 4) Turn +15 on and off until you reach the number of the function required (see table A), e. 5) Keeping +15 on, press button A once if you want to select the setting shown in the left hand column; press button A twice if you want to select the setting shown in the right hand column. 6) Switch +15 off and repeat the procedure from step 4 if you want to change any other settings. IMPORTANT: after you have programmed in a setting, the counter always starts again from the first function. 7) Four fast buzzer sounds confirm the end of programming; 8) Press button A on the remote control once when the key is in the OFF position to exit programming mode altogether. Key of the functions that can be programmed in: Buzzer = acoustic signalling of the arming and disarming of the alarm system. EMERGENCY DISARMING VIA THE OVERRIDE CODE Should your remote control be stolen or misplaced, stop working, or have a flat battery, you can disarm your alarm system by following an emergency procedure using the 5-digit OVERRIDE code shown on the CODE CARD. nB: THIS PROCEDURE WILL INEVITABLY TRIGGER AN ALARM AS IT INVOLVES USING THE IGNITION KEY. Each product has a different, factory-set OVERRIDE code, but this may be changed to a code of your choice. (See the "CUSTOMISING THE OVERRIDE CODE" section) Follow the procedure below in order to disarm the alarm system: Turn the ignition key to the ON position (+15) and check that the LED is now lit without flashing; A) Return the ignition key to the OFF position and wait for the LED to start flashing in order to confirm the first digit in the override code; CAUTION: THE NUMBER OF FLASHES MUST MATCH THE FIRST DIGIT IN THE CODE (E. IF THE FIRST DIGIT IS 1, TURN THE KEY TO THE ON POSITION WHEN THE LED HAS FLASHED ONCE) Confirm the digit by turning the key to the ON position; B) Return the ignition key to the OFF position and wait for the LED to start flashing in order to confirm the second digit; confirm the digit and repeat steps C-D and E for the remaining digits. If you have entered the correct code, the alarm will be disarmed once you have confirmed the fifth digit. You must start up the engine to confirm the whole operation; if you fail to do this, the alarm will remain armed. Caution: the control unit will enter a 30-minute block if incorrect codes are entered 3 times. CUSTOMISING THE OVERRIDE CODE You can customise the OVERRIDE code to a code of your choice by following the same procedure described above when the alarm system is disarmed: Within 10 seconds, turn the ignition key from the OFF position to the ON position (+15) 3 consecutive times; the LED will light up without flashing and you will hear a buzzer sound by way of confirmation; A) Return the ignition key to the OFF position and wait for the LED to start flashing in order to confirm the first digit in the override code. : if the first digit is 1, turn the key to the ON position when the led has flashed once); B) Within 3" return the ignition key to the OFF position and wait for the LED to start flashing in order to confirm the second digit; confirm the digit and repeat steps C-D and E for the remaining digits. Once you have confirmed the fifth digit, leave the key in the ON position (+15): if you have entered the correct code, the alarm system will emit four dual-tone buzzer sounds and the LED will turn off. ENTERING THE NEW CODE: F) Return the ignition key to the OFF position and wait for the LED to start flashing in order to confirm the first digit in the new code; G) Return the ignition key to the OFF position and wait for the LED to start flashing in order to confirm the second digit. [. . . ] The battery back up safeguards up to 9 alarm cycles, sounding for 26" with a 15" pause. The direction indicators do not operate when the alarm is operating on its battery back up supply. The battery back up is only operational when the alarm has been armed. Internal battery (back up power supply): the internal battery needs charging up if you hear 4 short warning signals after arming the alarm system. [. . . ]