User manual APPLIED ENERGY WHP210 BROCHURE

[. . . ] Heating Cooling and Dehumidifying all in ONE solution Digitemp for superior climate control The all-in-one solution for Heating, Cooling and Dehumidifying Most people have experienced the benefits of climate control in the car or at work. Your customers can now enjoy this comfort at home too with Digitemp. Installing climate control, an advanced form of air conditioning can bring a sense of comfort and style to a home, fulfilling the expectations of modern family life. Superior Climate Control By providing precise control of temperature, humidity and airflow the Digitemp climate control solution can dramatically reduce the effects of asthma allergies and other chest disorders. [. . . ] Using optimum heat pump efficiency, Digitemp can give you 2. 6kW of heating or 2. 2kW of cooling, using less than 1kW of electricity. All units benefit from R410a refrigerant, which as well as being the highest performing gas available, has an Ozone Depletion Power (ODP) rating of "0". All these factors combine to give Digitemp a capacity over absorption energy efficiency rating of up to A. Digitemp is sound insulated resulting in a quiet operation at only 37 decibels. The air quality is improved too; Digitemp uses a fine filter to clean the air, removing irritants like dust and pollen. Eco-friendly Digitemp creates an indoor environment that is healthy and brings comfort to life. total comfort at your fingertips The automatic control system provides precise climate control at the press of a button. All operational modes are programmable using the infrared handset - no need to move to adjust the room temperature. For peace of mind, Digitemp uses an automatic inbuilt diagnostic system which displays the condition of the unit through a series of LED's. Digitemp has a night function with reduced fan speed for quiet operation to help ensure a restful night's sleep. Superior Climate Control the range Four models are available in the range providing the choice between cooling only and heating or cooling. These are available in two capacities, with a maximum of 2. 45kW cooling. Wall mounted (low or high level) heating, cooling and dehumidifying climate control solutions COOLING ONLY Catalogue ref. Product code Cooling Capacity Heating Capacity EER (Energy Efficiency Ratio) COP (Coefficient of Performance) Max. Absorbed Power Rating Dehumidification Capacity Energy Efficiency Class Energy Efficiency Class Room Air Volume Fan Speed Settings Noise Levels Refrigerant Max Range of Infrared Remote Control Power Supply dB(A) Type m Volts Hz Dimensions (mm) Width Height Depth Weight Wall Hole diameter (min) mm W I/h Cooling Heating m /h 3 AIR CONDITIONING AND HEATING 91175AA WHP210 2. 1 1. 9 2. 23 2. 64 930 1. 0 A C 350 3 37 R410a 8 230 50 870 400 280 43 155 Unit kW kW 91173AA WA210 2. 1 2. 66 930 1. 0 A 350 3 37 R410a 8 230 50 870 400 280 43 155 91174AA WA245 2. 45 2. 66 1320 1. 2 C 390 3 39 R410a 8 230 50 870 400 280 46 155 91154AA WHP245 2. 45 2. 03 2. 23 1. 88 1320 1. 2 C F 390 3 39 R410a 8 230 50 870 400 280 46 155 installation guide. . . Key points to remember. There are some essential issues relating to the application and installation of the equipment which must be observed for problem free operation: The maximum length of ducting is one metre The unit must be mounted against an outside wall Where possible the unit should be positioned towards the centre of the selected wall and check weight specification The diameter of the supplied ducting must not be reduced or restricted The insulated duct must be used on the right hand side the product (viewed from the outside) and with the insulation adjacent to the rear of the unit It is essential that the units are installed perfectly level, failure to do so can lead to malfunction of the drip tray float valve causing water damage The units with reverse heat pumps must be provided with a means of drainage since the ice that forms on the coil is melted off every 30 minutes - this cannot be evaporated in the way the other condensate is discharged Care must be taken to ensure that the inlet and outlets are not obstructed in any way, such as by plants and bushes Only the inlet and outlet grilles supplied with the equipment must be used When the unit is mounted at high level, it is necessary to activate the room temperature differentiation function, this compensates for the stratification of heat The cored holes must be angled slightly downwards towards the outside to prevent any condensate running back into the unit For added flexibility Digitemp can be installed at high or low level to maximise floor space. [. . . ] Applied Energy Products reserve the right to alter product specification or appearance without prior notice. All finishes in the brochure are as accurate as printing processes allow. [. . . ]