User manual APPLIED ENERGY SB2

[. . . ] 6 Schematic wiring diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating Instructions General product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 How to operate the SB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 How to clean and descale your SB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 5b 5 Fixing the unit on the wall q Use the wall mounting bracket supplied and the two lower fixing holes. q An extra top fixing point is available by temporarily removing the condenser assembly. Connecting the water supply and vent pipes q When the unit is fixed to the wall, make the final water supply and steam vent connections and secure the pipe work. q Switch the water supply back on. Connecting the mains cable q Ensure the mains supply is isolated. q Connect the mains cable from the SB2 to the 13 Amp fused isolating switch. Ensure the cable clamps are firmly secured and the cable ends are tightened into the terminal block. Note: The supply cable must be a minimum of 1. 0mm2 three core multi strand PVC insulated mains cable. Check that the mains supply matches the electrical rating on the product. IMPORTANT: Connect the supply cable, complying with BS6500, to this appliance in accordance with the following code: GREEN AND YELLOW (EARTH) connect to terminal marked " ". BLUE (NEUTRAL) connect to terminal marked "N" BROWN (LIVE) connect to terminal marked "L" WARNING: THIS APPLIANCE, AND ALL METAL PIPE WORK CONNECTED TO IT, MUST BE EARTHED. Replacing the front cover q q q q Support the cover and re-attach the flying lead to the unit (See Fig. Replace the front cover and secure using the top and bottom fixing screws. Carefully replace the knob, ensuring correct alignment of the D shaft. Reconnect the mains supply. Schematic Wiring Diagram 6 Operating Instructions General Product Description The SB2 is a wall mounted, self calibrating and self filling boiling water heater. It can be used for making cups of tea or coffee and even soups and hot snacks. A special condenser traps steam and returns droplets to the tank, minimising waste and saving energy. The water temperature is set and automatically maintained by the SB2 and the unit is powered down with the Power button. Water is dispensed by rotating the front cover knob clockwise. How to operate the SB2 q Make sure the electricity and water is turned on. (The SB2 should be switched off at the mains if the water is not required e. g. (The SB2 fills up automatically and this can take up to 10 minutes if the tank is completely empty). TEMPERATURE READY light The TEMPERATURE READY light comes on when the water is hot enough to use. (This can happen even when the tank is not completely full of water). 7 Please Note: q The SB2 can take several minutes to reach the required temperature, depending on usage and tank capacity. q To avoid energy wastage, the SB2 will automatically reduce the temperature by 10ºC if the unit is not used for more than 60 minutes. (The SB2 will automatically go back to boiling when the water is used). [. . . ] 95719601 95719613 95719614 95719615 95719616 95719617 95719618 95719608 95719609 95719619 95719611 95719620 Part Description Element assembly Terminal block Logic board assembly Power PCB assembly Solenoid valve Float switch Cable pack Control knob Outlet Spout Scale Trap Outlet valve Inlet elbow assembly (includes flow regulator) 11 Guarantee We, Applied Energy Products Ltd. , guarantee that should this SB2 unit prove to be defective by reason of faulty workmanship or material within 24 months (outside of U. K. please contact your local distributor) of the date of purchase or commencement of hire we will replace or repair the defective parts FREE OF CHARGE on the condition that: a) The appliance has been correctly installed and used only on the supply circuit or voltage stamped on the rating plate. b) The appliance has been used in accordance with these instructions and has not been tampered with or otherwise subject to misuse, neglect or accident. c) The appliance has not been taken apart, modified or repaired except by a person authorised by us. [. . . ]