User manual APPLIED ENERGY MW-EW 15

[. . . ] f) Evidence of the date of purchase in the form of an invoice or receipt will be required in order to qualify under the terms of this guarantee. g) For the service work to be undertaken free of charge, the work must only be undertaken by Applied Energy Products Limited, or our approved agents. The guarantee on any exchanged parts or product ends when the original guarantee period ends. i) In the event of a product being returned to Applied Energy Products Limited and not found to be faulty, the product would be available for collection from the relevant premises within one month and if not collected it would be disposed of or delivered by Applied Energy Products Limited and a delivery charge made. [. . . ] It is the responsibility of the installer to check that the installation parameters meet the requirements of the product, and any relevant regulations. If we are called out to investigate a fault, which is subsequently identified as being an installation fault, we will make a charge. It is important that the routine checks are completed before calling us out, as many issues can be simply diagnosed and resolved. We will endeavour to achieve the most timely response possible but while we indicate an average response time, this should not be taken as a guarantee. The guarantee applies to a repair or replacement (at our discretion) of the product subject to the conditions above, and DOES NOT cover compensation for the loss of the product or consequential loss of any kind. This guarantee covers products supplied by Applied Energy Products only, and does not cover other products and components used to create a system that have not been purchased from Applied Energy Products. The responsibility for the suitability of the complete system for the specific application remains the responsibility of the original specification engineer. This guarantee does not affect your statutory rights. R R Xplus Ultra DC Continuous extract MEV unit Xplus 250DC 8CV Xplus 400DC 8CV Applied Energy Products Ltd Morley Way Peterborough PE2 9JJ tel 01733 456789 fax 01733 310606 Technical line 08709 000430 Technical fax 08709 000530 Xpelair is a registered trademark of Applied Energy Products Limited. Applied Energy Products reserve the right to alter product specifications or appearance without prior notice. All finishes and diagrams in this booklet are as accurate as printing processes allow. 8 Leaflet Part No. The fan can be wired for direct operation as fig B1 or through an Xpelair XRH (fig B2), AQS (fig B3), COS switch (fig B4), DT20B (fig B5) or XPIRA (fig B6), where the controller provides the Boost function to the fan. Connect the cable from the isolating switch to the electrical supply wiring. Note: For fixed wiring circuits, the protective fuse for the appliance must not exceed 5A. Operating the fan 1. The fan should be set to provide the performance requirements according to the dwelling size by adjusting the switch on the side of the unit. Altering the switch position when the unit is powered will not change the speed setting. The fan has 8 speed settings: Setting 1 2 3 4 5 6 7 8 Performance (m³/h) Xplus 250 Xplus 400 48m³/h 78m³/h 93m³/h 100m³/h 156m³/h 170m³/h 174m³/h 229m³/h 206m³/h 236m³/h 243m³/h 254m³/h 304m³/h 333m³/h 341m³/h 389m³/h The fan provides constant volume performance for system pressures up to 300Pa Cleaning The fan can be mounted to a suitably strong wall or roof member. Position of the air outlet At least 0. 5m away from open door or window, or the inlet of another ventilation device. Installing the ducting 1. Detach the appropriate inlet covers after removing the fixing screws. Install the ducting to connect the fan to the air intakes and to the outlet. If installing in a position where condensation is likely to run back towards the fan, install a condensation trap as near to the fan as possible. Mounting the fan Description Xplus 250DC 8CV / Xplus 400DC 8CV 1. Apart from cleaning, no other maintenance is required. Choice of 8 extraction speeds, selectable at installation according to house size. Boost speed available at each extraction speed when used with an appropriate controller (not supplied). [. . . ] Boost speed available at each extraction speed when used with an appropriate controller (not supplied). Three 125mm diameter inlet spigot connections and a 125mm diameter outlet. 2. 3. 4. What the installer will need A means for disconnection in all poles must be incorporated in the fixed wiring in accordance with the wiring rules. Ducting long enough to connect from the position of the air intake positions to the air outlet via the fan. [. . . ]