User manual APPLIED ENERGY EXPRESSIONS 500S

[. . . ] REDRING EXPRESSIONS 500S SMART TECHNOLOGY ELECTRIC SHOWER Installation and User Guide IMPORTANT: This booklet should be left with the user after installation and demonstration CONTENTS Section Page Introduction _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Important Safety Information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 How to use your Expressions 500S Shower (Detailed) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 How your Expressions 500S Shower Works _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 How to maintain your Expressions 500S Shower _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 What to do if things go wrong (1) Self Help _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 What to do if things go wrong (2) Professional Service _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Redring After Sales Service _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 How to install your Expressions 500S Shower _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Additional Accessories and Spare Parts _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Guarantee and Contact Details _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 How to use your Expressions 500S Shower (Summary) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12 INTRODUCTION Thank you for purchasing a quality Redring Expressions 500S Shower manufactured in England. To enjoy your new shower at its best, please take time to read this manual thoroughly, and having done so, keep it handy for future reference. The Redring Expressions 500S is an electric shower incorporating our "Smart Technology" with a "Set and Forget" function of a push-button start/stop facility which starts the shower at a pre-set power and flow rate reducing the amount of adjustment required. Your shower is designed to stabilise temperature changes caused by water pressure fluctuations. [. . . ] It is therefore important to clean the shower handset by simply rubbing the rubber nozzles. NOTE: After use it is normal for some water to drip from the shower handset for a few moments. This inhibits scale build-up over prolonged use. WHAT TO DO IF THINGS GO WRONG (1) SELF HELP If the shower is unsatisfactory, make the following checks before calling out the contractor. Any one of these adjustments could restore the performance. The shower cycles from HOT to COLD The shower temperature is set too hot causing the thermal cut-out (safety device) to operate. Turn knob "C" clockwise (direction of the "blue arrows") to increase water flow. Slowly increase the water temperature by turning knob "C" anti-clockwise in the direction of the "red arrows" until a comfortable showering temperature has been reached. You MUST WAIT approximately 20 seconds for each adjustment to affect the water temperature. Increase water flow by adjusting knob "C" clockwise (direction of the "blue arrows"). Decrease water flow by adjusting Knob "C" anti-clockwise (direction of the "red arrows"). Thermal cut-out has operated after previous use ("Overheat" light is on) (automatically resets when unit cools down) "High" setting may need to be selected. Check water pressure has not fallen so far as to let pressure switch cut out, e. g. Raise position of shower handset. Water too HOT Water too COLD Spray pattern poor Water takes longer to heat up Water goes cold while using shower 5 Water continues to flow when button "B" pressed Broken parts This is normal. RING 08709 000420 (UK ONLY) Remember to quote the exact type of shower, as written on the front of the shower and on this leaflet. 6 The model and serial number are located on the bottom face of the shower. Make a note of those numbers here, and be sure to quote them if you call for advice. Model Number: 53-67_ _ _ _ _ _ _ _ _ _ _ _ _ Serial Number: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ HOW TO INSTALL YOUR EXPRESSIONS 500S SHOWER WARNING: ALL WIRING AND INSTALLATION MUST BE SUPERVISED BY A SUITABLY QUALIFIED PERSON. WARNING: DO NOT INSTALL THIS SHOWER WHERE IT MAY BE SUBJECTED TO FREEZING CONDITIONS We recommend that the installation is done in the following sequence. Position the riser rail at the height recommended in diagram 5 and mark its position (also see separate accessories fitting instructions). Position the heater so that the top of the unit is horizontal and level with, or a maximum of 0. 6 metres (2ft) below the top of the riser rail. Choose a flat piece of wall to avoid the possibility of distorting the backplate thus making the front cover a poor fit. Adjust the position to get the most convenient arrangement taking the following into account. · The possible need to use the handset over the sink for hair washing etc. · · The heater must not be mounted in the direct spray from the handset. [. . . ] Check that knob "A" has been correctly aligned by ensuring that all 3 power settings can be selected. Check that knob "C" has been correctly aligned by turning anti-clockwise and ensuring that knob turns 1 approximately 1 full turn and when turned back fully clockwise, returns to "12 o'clock". 6. Fit the shower hose, and operate the shower first without the handset to flush out particles, fit the handset and then operate the shower as on page 3 or 12 and check: a. Power selection operates in all 3 positions, giving a change in water temperature and that the power indictor lights functions correctly. [. . . ]