User manual APPLIED ENERGY DX100PIR

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual APPLIED ENERGY DX100PIR. We hope that this APPLIED ENERGY DX100PIR user guide will be useful to you.


APPLIED ENERGY DX100PIR : Download the complete user guide (12923 Ko)

Manual abstract: user guide APPLIED ENERGY DX100PIR

Detailed instructions for use are in the User's Guide.

[. . . ] If ceiling mounting the fan You will need to use the appropriate ancillaries for termination. When the fan is switched off, it will continue to operate for approximately 7. At least 110mm from the edges of the As far away as possible from and opposite to Not where ambient temperatures are likely Airflow across the room (e. Flexible 2-core cable complete with 3 pin plug for insertion into an approved 10 amp GPO or directly wired through an approved 10A wallmounted surface switch with at least 3mm clearance between contacts. [. . . ] Make all connections within the isolating switch and the on/off switch (if required). Note: on/off switch must be situated so that it cannot be touched by persons making use of the bath or shower. DX100HP & DX100PIR) Connection to the supply can be made by a Please leave this leaflet with the fan for the benefit of the user If the shaft has cavity wall, use the wall tube to bridge the cavity. Fit ducting and condensation trap if necessary, positioning condensation trap as near to the fan as possible. Preparing the fan for installation Remove the front cover by pressing the release catches located on the sides of the unit with a 3mm screwdriver, whilst pulling the front cover forward L Mount the fan in the hole If working above ground floor level, appropriate safety precautions must be observed. If installing in a wall, ceiling or vent Mark the position of the back plate B 1. Hold the backplate so that the terminal block faces you in the top left hand corner and the lip points towards the hole. Mark on the wall/ceiling or vent shaft the positions of the three fixing holes in the back plate. Drill screw holes in these positions if necessary, and fit wall plugs if necessary. If installing in a ceiling or vent, push the larger diameter piece of the telescopic wall tube onto the ribbed gasket. Feed the mains cable through the cable entry hole in the back plate to the terminals D. If wiring from above, leave the cable free to be fitted into labyrinth. Insert the lip of the back plate into the wall duct/ceiling or vent shaft as before. Fasten the back plate to the wall/ceiling or vent shaft using appropriate fasteners. Peel the backing from the foam strip supplied and attach it around the outside of the lip on the back draught shutter. Holding open the top and bottom vanes, insert the lip into the wall duct. Making sure that the back draught shutter is level, mark the positions of the two fixing holes in the top right hand and bottom left hand corners. Drill screw holes in these positions, and fit the remaining wall plugs. Holding open the top and bottom vanes, refit the back draught shutter and fasten it to the wall using the pointed and self-tapping screws. If installing in a window or panel no more than 9mm thick, fit the white rubber gasket around the edge of the hole. if installing in a panel or sealed double glazing more than 9mm thick , a DXDG double glazing kit is required. Holding the top and bottom vanes, insert the back draught shutter 2 into the spacer 3 so that the fixing holes in the top right and bottom left hand corners match those on the spacer. [. . . ] When the fan is first installed there will be a stabilising period of approximately five minutes. Våra tekniker finns till hands enbart på kontorstid (enbart Storbritannien), men du kan faxa dina frågor till hjälplinjen när som helst på numret +44 (0) 8799 000530. Se till att strömmen är bruten till fläkten innan något rengöringsarbete påbörjas . Do install each fan with a double pole isolating switch with a contact gap of 3mm in each pole. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE APPLIED ENERGY DX100PIR




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual APPLIED ENERGY DX100PIR will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.