User manual APPLIED ENERGY ACTIVE 320S

[. . . ] REDRING ACTIVE 320S SMART TECHNOLOGY ELECTRIC SHOWER Installation and User Guide IMPORTANT: This booklet should be left with the user after installation and demonstration CONTENTS Section Page Introduction _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Important Safety Information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 How to use your Active 320S Shower (Detailed) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 How your Active 320S Shower Works _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 How to maintain your Active 320S Shower _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 What to do if things go wrong (1) Self Help _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 What to do if things go wrong (2) Professional Service _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Redring After Sales Service _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 How to install your Active 320S Shower _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Additional Accessories and Spare Parts _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Guarantee and Contact Details _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 How to use your Active 320S Shower (Summary) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12 INTRODUCTION Thank you for purchasing a quality Redring Active 320S Electric Shower manufactured in England. To enjoy your new shower at its best, please take time to read this manual thoroughly, and having done so, keep it handy for future reference. The Redring Active 320S is an electric shower incorporating our "Smart Technology" and a unique dual control combining on/off, power select and flow/temperature control. Your shower is designed to stabilise temperature changes caused by water pressure fluctuations. [. . . ] This inhibits scale build-up over prolonged use. WHAT TO DO IF THINGS GO WRONG (1) SELF HELP If the shower is unsatisfactory, make the following checks before calling out the contractor. Any one of these adjustments could restore the performance. The shower cycles from HOT to COLD The shower temperature is set too hot causing the thermal cut-out (safety device) to operate. Turn inner knob "B" anti-clockwise in the direction of the "blue arrows" to increase water flow. Slowly increase the water temperature by turning inner knob "B" clockwise in the direction of the "red arrows" until a comfortable showering temperature has been reached. You MUST WAIT approximately 20 seconds for each adjustment to affect the water temperature. Increase water flow by adjusting inner knob "B" anti-clockwise (direction of the "blue arrows"). Decrease water flow by adjusting inner knob "B" clockwise (direction of the "red arrows"). Thermal cut-out has operated after previous use (automatically resets when unit cools down) " (high)" setting may need to be selected. Check water pressure has not fallen so far as to let pressure switch cut out, e. g. Raise position of shower handset. Water too HOT Water too COLD Spray pattern poor Water takes longer to heat up Water goes cold while using shower 5 Water continues to flow when " (stop)" selected Broken parts This is normal. The shower includes a shutdown feature that means the water will continue to flow for up to 3 seconds after " (stop)" has been selected. Fitting instructions are provided with most spares WHAT TO DO IF THINGS GO WRONG (2) PROFESSIONAL SERVICE If the previous "Self Help" checks fail to restore the performance, you should seek professional help. The person who installed the shower is probably the best one to repair it and is certainly the person to contact if you have had a problem in the guarantee period. The following additional checklist is provided for the benefit of the qualified service person. WARNING: SWITCH OFF THE ELECTRICITY AT THE LOCAL ISOLATOR BEFORE REMOVING THE COVER TO MAKE CHECKS Water too HOT Water flow restricted by blockage in filter of solenoid valve. Switch off water, loosen inlet connection to solenoid, remove filter in solenoid with long nosed pliers and flush clean. Choose a flat piece of wall to avoid the possibility of distorting the backplate thus making the front cover a poor fit. Adjust the position to get the most convenient arrangement taking the following into account. · The possible need to use the handset over the sink for hair washing etc. · · The heater must not be mounted in the direct spray from the handset. The handset must not be able to come into contact with used water in the cubicle, bath or basin. If it can, even after the hose has been retained by the soap dish (see separate accessories fitting instructions sheet) then a vacuum breaker must be fitted. 4. [. . . ] In the main body of the shower, turn the "Drive Gite" anti-clockwise until it is at "12 o'clock". Fit the front cover of the shower to the main body ensuring that the 3 x "Drive Spider Legs" engage with the slots in outer knob "A". Check that outer knob "A" has been correctly aligned by ensuring that all 3 power settings can be selected, and returns to the " (stop)" position. Check that inner knob "B" has been correctly aligned by turning clockwise and ensuring that knob turns approximately 3/4 of a turn (270°) and when turned back fully anti-clockwise, returns to the " (high)" position. 6. [. . . ]