User manual APOGEE AMBUS DIGI8+ CARD

[. . . ] Digi-8+ Card Operating Information v3. 1. 0 AMBus Digi8+ Card for Pro Tools, Firmware Rev 3. 1. 0 Getting Started Quickly! Beginning with firmware version 3. 1. 0, Apogee interfaces may be clocked in precisely the same manner as any Digidesign interface!If you're not familiar with signal routing within your Apogee system, you may want to read on; otherwise, you may now close the manual! Installing the AMBUS card Before installing the AMBus card, ensure that the unit is powered down. As is the case with all AMBus cards, care must be taken to avoid damage from static discharge. [. . . ] With the following rules, virtually any combination of interfaces may be correctly configured. 1) When clocking an Apogee interface from a MOTU DTP or Digidesign USD, it is preferable to use Super (Slave) Clock. 2) Given the exception noted above, Apogee interfaces may be clocked using either Word Clock or Super (Slave) Clock. Slave Clock I/O is found on the Dig8+ card, while Word Clock is found on the interface chassis. 3) Digidesign interfaces must be clocked with Super (Slave) Clock ONLY. 4) When using Super (Slave) clock on either a Digidesign or Apogee interface, clock cables must be connected from the Super (Slave) Clock out of the master interface to the Super (Slave) Clock in of interface 2, Slave Clock Out of interface 2 to Slave Clock In of interface 3, and so on until all interfaces have received a clock signal 5) When using Word Clock with Apogee interfaces, Word Clock out from the master interface should be connected to one side of a BNC "T" connector at the Word Clock in of interface 2. The other side of the BNC "T" connector goes to a similar BNC "T" connector on interface 3, and so on until all interfaces have received clock. Connect a 75 ohm termination plug to the unused side of the BNC "T" on the LAST interface (see Fig. 3). Page 1 Digi-8+ Card Operating Information v 3. 1. 0 Working with Pro Tools After configuring your hardware interfaces, you'll need to configure the Pro Tools application so that it recognizes the interfaces. Please see Digidesign's TDM Hardware Installation Guide for precise details, remembering that Apogee interfaces should be configured as an 888/24. Unlike meters on Digidesign interfaces, Apogee interface meters display the signal level before being sent to the Pro Tools application. We feel that input level is the highest priority in digital recording, and have built our interfaces accordingly. DIP Switches The default position for the DIP switches found on the Digi8+ card is shown at right. All switches are pressed towards OPEN 1 2 3 4 5 6 7 8 OPEN When DIP switch 2 is pressed away from OPEN (as shown at right), certain settings on the AD-8000 may be controlled from Pro Tools: Pro Tools Settings AD-8000 Settings Session Sample Rate determines Sample Rate Sync Mode sets Sync Source* Digital Format sets Source* Ch 1-2 Input sets Channel 1-2 input* * note that the only Digital formats selectable from Pro Tools are the AES and S/PDIF chassis mount inputs. For from of AD-8000 Tools systems, DIP switch 3 reverses odd/even audio pairs from Pro Tools when pressed away from OPEN, while DIP switch 4 reverses odd/even audio pairs to Pro Tools when pressed away from OPEN 1 2 3 4 5 6 7 8 OPEN 1 2 3 4 5 6 7 8 OPEN For Extra Credit (Clock Experts) Version 3. 1. 0 firmware makes Apogee-equipped Pro Tools systems highly tolerant of clock phase differences caused by latency, as long as all devices are ultimately clocked from the same source Signal Routing in Apogee Interfaces The AD-8000 and Trak2 interfaces share the same extremely flexible signal routing architecture, which may configured in the two general signal paths depicted on the next page. When working with Pro Tools, you'll want to set the AD-8000 to "Destination" mode and the Trak2 to "Confidence Mon ­ ON" mode, with the Digi8+ card selected as the "target" AMBus card. To configure the AD-8000 for use with Pro Tools: · Press and Hold the "STEREO SEL" button until the "DEST" LED illuminates · Without releasing the "STEREO SEL" button, toggle the Headphone "VOLUME" switch until the AMBus Slot Letter (A, B, C or D) into which your Digi8+ card is installed appears in the 7-segment window to the left of the Headphone "VOLUME" toggle switch. [. . . ] If "Y" cable is used, connect to "A" side AD8K #1 WC Out to BNC "T" connected to AD8K #2 WC+VID In. From PT Farm Card or "B" side of Y cable if used From AD8K #2 to BNC "T" connected to AD8K #3 WC+VID In. 75 ohm terminator connected to unused side of BNC "T" From PT Farm card MOTU Digital Time Piece (or Digidesign USD) + 2 AD-8000s + Digidesign 888 DTP (or USD) Super Clock Out to AD8K #1 Slave Clock In From PT Core Card, "A" side if Y cable used AD8K #1 WC Out to BNC "T" connected to AD8K #2 WC+VID In. 75 ohm terminator connected to unused side of BNC "T" From PT Farm Card or "B" side of Y cable if used AD8K #1 Slave Clock Out to 888 Slave Clock In From PT Farm card Page 5 [. . . ]