User manual AOPEN SX34G

[. . . ] The CPU core voltage will be automatically detected and the range is from 1. 05V to 1. 825V. It is not necessary to set CPU Core Voltage Setting CPU Frequency This motherboard is CPU jumper-less design, the system can detect the CPU frequency automatically, and no jumpers or switches are needed. BIOS Setup > Frequency / Voltage Control > CPU Speed Setup Core Frequency = CPU FSB Clock * CPU Ratio CPU socket lever 3. CPU Pin 1 and cut edge Note: If you do not match the CPU socket Pin 1 and CPU cut edge well, it may damage the CPU. CPU Pentium III 800E Pentium III 850E Pentium III 533EB CPU Core Frequency 800MHz 850MHz 533MHz 600MHz 667MHz 733MHz 800MHz 866MHz 933MHz 1GHz 1. 13GHz 1. 26GHz FSB Clock 100MHz 100MHz 133MHz 133MHz 133MHz 133MHz 133MHz 133MHz 133MHz 133MHz 133MHz 133MHz Ratio 8x 8. 5x 4x 4. 5x 5x 5. 5 6x 6. 5 7x 7. 5x 8. 5x 9x 4. [. . . ] A slim-type floppy disk drive is connected with a special design cable. Installing DIMM Sockets This motherboard supports Advanced ECC memory Controller, 168-pin PC100 / PC133 SDRAM, Virtual Channel Memory (VCM), and ESDRAM up to 3GB. Dimm3 Dimm2 Dimm1 RAID primary channel RAID secondary channel CD-ROM drive connector 14. Support 10/100 Mbps LAN Onboard On the strength of Intel 82550 PHY on board, which is a highly-integrated Platform LAN Connect device, it provides 10/100M bps Ethernet for office and home use, the Ethernet RJ45 connector is located on the back panel. The green LED indicates the link mode, it lights when linking to network and blinking when transferring data. The orange LED indicates the transfer mode, and it lights when data is transferring in 100Mbps mode. To enable or disable this function, you may simply adjust it through BIOS. 16. Back Panel The picture shown below indicates the functions of all connectors on the real panel. Please make sure you plug in the right direction. PS/2 Keyboard RJ45 LAN Jack Green/ACT Orange/Speed ATX Power Connector System event LED PS/2 Mouse COM1 VGA Connector 15. PCI Bus Slots The Fortress1100 has two 32-bit / 33 MHz PCI bus slots with a riser card. The riser card provides an easy way to plug the PCI card in the system. 17. Front Panel The picture shown below indicates the functions of LEDs of the front panel. Please make sure you plug in the right direction. Riser Card System health LED Hard Disk LED Power LED USB Ports Reset Button Power Button 18. Power-On and Load BIOS Setup After you finish the setting of jumpers and connect correct cables. Power on and enter the BIOS Setup, press <Del> during POST (Power On Self Test). Choose "Load Default Setting" for recommended optimal performance. Del If you encounter any trouble to boot you system, follow the procedures accordingly to resolve the problem. Start Turn off the power and unplug the AC power cable, then remove all of the addon cards and cables, including VGA, IDE, FDD, COM1, COM2 and Printer. Make sure if the jumper settings for CPU and DRAMs are correct. Clear CMOS. Install the VGA card. Then connect your monitor and keyboard. Turn on the power, and check if the power supply and CPU fan work properly. No The problem was probably caused by power supply or motherboard failure. Please contact your reseller or local distributor for repairing. Yes No Check if there is display. Perhaps your VGA card or monitor is defective. Yes 19. Part Number and Serial Number The Part Number and Serial number are printed on bar code label. You can find this bar code label on the outside packing, on ISA/CPU slot or on component side of PCB. [. . . ] http://www. aopen. com/tech/faq/default. htm 4 5 Download Software: Check out this table to get the latest updated BIOS/utility and drivers. http://www. aopen. com/tech/download/default. htm China ¦ã (ªÑ )¦³-¤½¥q Tel: 86-21-6225-8622 Fax: 86-21-6225-7926 Germany AOpen Computer GmbH. Tel: 49-2102-157700 Fax: 49-2102-157799 News Group: Our support engineer or professional users on the news group probably had answered your problem. [. . . ]