User manual AOPEN DX3RG

[. . . ] For more information, a complete Online User's Manual can be found in the Bonus Pack CD Disc. Thanks for the help of saving our earth! 3. Note: If you do not match the CPU socket Pin 1 and CPU cut edge well, it may damage the CPU. CPU socket lever Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Hard Drive IDE Cable x 1 Ultra 160 SCSI 68 pin Cable x 1 Ultra Narrow 50 pin Cable x 1 nd 2 USB cable x 1 COM Port Cable x 1 Bonus Pack CD x 1 Norton Anti-Virus CD x 1 ASM Lite CD x 1 CPU Terminator x 1 IO Bracket for SV520 x 1 IO Bracket for Open Market Housing x 1 SCSI Utility Diskette Pack x 1 Screw Pack x 1 User Manual x 1 This Easy Installation Guide x 1 2. Installing CPU & Housing Fan Plug in the CPU fan cable to the 3-pin CPU FAN connector and housing fan cable to the Housing Fan connector. GND +12V Sensor CPU fan +12V Fan Off (GND) Fan Fail Sensor Note: Some CPU fans do not have sensor pin, so that cannot support fan monitoring. PART NO: 90. 58C01. 002 DOC. [. . . ] Two of them are on back panel connector, the other two are on the left-bottom area of this motherboard. With proper cable, you can connect them to front panel. USBPWR6 USBP2GND USBPWR7 USBP3+ USBP3USBPWR5 1 2 21 22 USBP2+ USBPWR8 HDD LED Reset Switch +5V GND PWR LED +5VSB 1 2 GND +5V HDD LED HDD LED +5V GND RST S/W INT S/W 21 22 GND GND 12. WOL (Wake on LAN) Connector To use Wake On LAN function, you must have an Ethernet card with chipset that supports this feature, and connect a cable from LAN card to motherboard WOL connector. The system identification information (probably IP address) is stored on network card and because there is a lot of traffic on the Ethernet, you need to install network management software, such as ADM, for the checking of how to wake up the system. 14. NMI (Non-Maskable Interrupt) Switch Jumper Non- Maskable Interrupt used for event handling. When event is occurred, system will receive an NMI and execute a unique task. To disable this function, please short CN18 by jumper cap. Close Open (Default) +5VSB GND LID 15. BP (Backplane) Connector The BP connector provides the signals of BPL6 / BPL5 back plane to ASM (Advanced Server Management) software monitoring program, such as storage category, HDD fault, fan present, and fan fault. 17. Event LED Connector The DX3R Plus BIOS supports the system monitored event logs recording function. If there is any event happens or hard disk fails when you operate your system, the Event LED will keep flash to warn you. Pin 1 Pin 1 1 GND N/C I2C CLK I CDA 2 1 To LED GND 16. External Speaker Connector If you want to use external case-mounted speaker instead of internal buzzer, the 4-pins external speaker connector can let you connect with external case-mounted speaker. 18. Power-On and Load BIOS Setup After you finish the setting of jumpers and connect correct cables. Power on and enter the BIOS Setup, press <Del> during POST (Power On Self Test). Choose "Load Default Setting" for recommended optimal performance. Del Pin 1 GND N/C N/C +5V Warning: Please avoid of using "Load Turbo Defaults", unless you are sure your system components (CPU, DRAM, HDD, etc. ) are good enough for turbo setting. Part Number and Serial Number If you encounter any trouble to boot you system, follow the procedures accordingly to resolve the problem. You can find this bar code label on the outside packing, on ISA/CPU slot or on component side of PCB. For example: Start Turn off the power and unplug the AC power cable, then remove all of the addon cards and cables, including VGA, IDE, FDD, COM1, COM2 and Printer. Make sure if the jumper settings for CPU and DRAMs are correct. Part No. Serial No. Clear CMOS. Install the VGA card. Then connect your monitor and keyboard. Part No. Serial No. P/N: 91. 88110. 201 is part number, S/N: 91949378KN73 is serial number. Turn on the power, and check if the power supply and CPU fan work properly. No The problem was probably caused by power supply or motherboard failure. Please contact your reseller or local distributor for repairing. Yes No Check if there is display. Perhaps your VGA card or monitor is defective. Yes Press Ctrl, and Alt key at the same time, hold them and then press Del to see if the system reboots. No It is very possible that your keyboard is defective. Yes During system rebooting, press Del to enter BIOS Setup. [. . . ] Tel: 49-2102-157700 Fax: 49-2102-157799 News Group: Your problem probably had been answered by our support engineer or professional users on the news group. http://www. aopen. com/tech/newsgrp/default. htm America AOpen America Inc. Tel: 1-510-498-8928 Fax: 1-408-922-2935, 1-408-432-0496 6 7 Contact Distributors/Resellers: We sell our products through resellers and integrators . They should know your system configuration very well and should be able to solve your problem more efficien n important reference for you if next time you want to buy something else from them. Web Site: www. aopen. com E-mail: Send us email by going through the contact form below. [. . . ]