User manual AOPEN DRW8800APP0403A

[. . . ] · Do not use specially shaped disks such as heart shape or polygon. Note: In accordance with Part 15 of FCC, it has been confirmed that this equipment has passed the test and meets the restrictions on Grade-B digital model. The purpose of design restriction is to provide reasonable protection for home appliance against harmful interference. Because this equipment generates, uses and emits an infinite frequency, harmful interference may be caused to the wireless communication if failure to install and use this equipment according to the instructions contained in the manual. In spite of this, we do not guarantee that interference will not be caused to some specific facilities. [. . . ] Cleaning: Do not use liquid, aerosol cleaner or alcohol; instead, wet rags should be used to clean the housing surface only. Power SourceBe sure to operate this product according to the power indicated in the label. IF the power type cannot be ascertained, consult an authorized Pioneer dealer. Overload: Do not overload the wall socket and power cord to avoid fire or electric shock hazards. Invasion of Foreign Object and Moisture: Do not put any type of object in this product that could cause a short circuit and lead to fire or electric shock when contacting the hazardous voltage. Condensation: When the unit is moved from a cold area into a warm environment, moisture can form around the operational part and damage the performance. To move the unit to a warmer location, place the product in the new environment for 1 to 2 hours before turning it on. Maintenance: Do not attempt to repair this product, which could put you at risk of contact with a hazardous voltage or other danger after opening or removing the cover. Instead, you should ask a qualified person to perform all maintenance works (please refer to the provided maintenance backup card) · Remove the dust on the disk with soft cloth or cotton ball by rubbing from inside toward outside instead of circling the disk. · Do not use disk cleaner or anti-static agent to avoid hurting the disk with the solvent. Before use, be sure to check if dirt or dust is left on the disk (especially the recording face). Features · Writing Speed DVD-R, at 8X-Zone CLV, 6X-CLV, 4X-CLV, 2X-CLV, 1X-CLV. Reading Speed: DVD-ROM (single layer), at CAV 12X DVD-ROM (double layer), at CAV 8X DVD-R and DVD-RW, at CAV 8X DVD-RAM, at CLV 2X DVD+R and DVD+RW, at CAV 8X CD-ROM and CD-R, at CAV40X / CD-RW: CAV 32X. · Buffer Memory Capacity: 2 Mbyte (writing, reading) · IDE Data Transmission Mode PIO Mode 4, Multi Word DMA Mode 2 , Ultra DMA Mode2 · Backup Video CD · 5. 25 " half-height built-in type. · LCD Split Server · Available in horizontal/vertical direction. Disk Format (reading/writing) · DVD single layer/double layer /120mm disk/80mm disk. · DVD-R (Ver. 2. 0) · DVD-RW(Ver. 1. 0 & Ver. 1. 1 & Ver. 1. 2 ) · DVD+R(Ver. 1. 0 & Ver. 1. 1 & Ver. 1. 2) · DVD+RW(Ver. 1. 1 & Ver. 1. 2) · CD-ROM Mode 1 · CD-ROM XA Mode 2(Form 1, Form 2) · Photo CDSingle/Multiple Session · CD-DA · CD-Extra (CD PLUS) · CD-R · CD-RW, Ultra-speed CD-RW Note: Special application programs supporting the above-said format must be written. Interface Front View 1 Force Eject Hole If the tray fails to eject upon pressing the Eject button, insert the eject pin into the hole and then push out the tray from within. At this time, confirm the drive power has been disconnected and then wait for over one minute until the disk stops turning before inserting the pin in the eject hole. 2 Data Processing Indicator The indicator below shows the operation situation: Reading Indicator on Writing Indicator on 3 Eject Push Button Push this button to eject/load the disk. 4 Disk Tray Push Eject button and open the tray and then load the CD or DVD, with label facing upward. Note for playing 8cm (3. 15") disk: When the drive is in the erected position, the unit cannot play 8cm (3. 15") disk even if the disk is engaged with the adapter. Rear View 6 Audio Output Port Analog audio output connector used. [. . . ] At this time, ensure that Pin #1 of the drive IDE Connector has properly connected with Pin #1 of the cable. · When using the Sound Card, be sure to connect the audio output port and the sound card with the audio cable. Confirm the power required for this product provided by the connected PC. Do not use any other power source besides the PC power. Pin #1 Audio Cable IDE Interface Power Specification [Installation] This drive is available for vertical and horizontal application. [Disk Size] · 12cm (4. 72") / 8cm (3. 15")* * 8cm (3. 15") cannot be used in vertical application. [. . . ]