User manual AOPEN CD32X

[. . . ] AVATTAESSA OLET ALTTINA LASERSÄTEILYLLE VARNING: LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD ÄLÄ TUIJOTA SÄTEESEEN STIRRA EJ IN I STRÅLEN LUOKAN 1 LASERLAITE LASER KLASSE 1 VORSICHT: UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHLL AUSSETZEN. PRODUCTO LÁSER DE LA CLASE 1 ADVERTENCIA: RADIACIÓN LASER INVISIBLE AL SER ABIERTO. EVITE EXPONERSE A LOS RAYOS. VARNING: LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD STIRRA EJ IN I STRÅLEN ADVARSEL: LASERSTRÅLING NÅR DEKSEL ÅPNES STIRR IKKE INN I STRÅLEN Copyright Copyright © 1997 by this company. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. Disclaimer This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. [. . . ] 5. Audio Cable Power Cable Red Strip IDE Cable Red Strip NOTE: The red edge of the IDE cable corresponds to pin 1 of the IDE interface on the CD-ROM drive. If you have a sound card, you can also connect a 4-pin analog audio cable to the analog audio-out connector of your CD-ROM drive and the audio-in connector of the sound card. If you have a digital audio device, you can also connect a 2-pin digital audio cable to the digital audio-out connector of your CD-ROM drive and the audio-in connector of your digital audio device. Replace the cover and turn on the power. v 2 Installing the CD-ROM Drivers The CD-ROM package comes with an installation utility. This utility installs the CD-ROM drivers needed by your CD-ROM drive to interact with your PC. The driver installation diskette includes the following files: · · · · AOATAPI. SYS INSTALL. EXE README. TXT READMEJ. TXT NOTE: The INSTALL. EXE file automatically detects the system language environment. For DOS and Windows 3. 1 To install the driver in DOS or Windows 3. 1: 1. Insert the installation diskette in your 3. 5-inch diskette drive and make it the active drive. The installation program creates a directory (C:\CDROM) containing the CD-ROM drivers. It also updates your AUTOEXEC. BAT and CONFIG. SYS files as follows: CONFIG. SYS DEVICE=C:\CDROM\AOATAPI. SYS /D:IDECD000 LASTDRIVE=N AUTOEXEC. BAT C:\DOS\MSCDEX. EXE /D:IDECD000 Changing the Settings After Installation To reconfigure the settings of the CD-ROM driver, use a text editor (such as EDIT. COM) to modify the DEVICE= and LASTDRIVE= command lines in the CONFIG. SYS and AUTOEXEC. BAT files. Then restart your computer. Table of Contents Changing the CONFIG. SYS File and Enabling the DMA Function Add the following line to your CONFIG. SYS: DEVICE = <PATH>\AOATAPI. SYS /D:<DEVICE_NAME> [/zzzz] [/P:xxx, yy] The <DEVICE_NAME> is the name of the MSCDEX file that will be used to find the device driver. The maximum length of the <DEVICE_NAME> string is eight characters. The option [/zzzz] in character form specifies the DMA function, the Ultra-DMA 33 function or Bus Master DMA function. For example: DEVICE=C:\CDROM\AOATAPI. SYS /D:IDECD000 /DMA /P:1F0, 14 If your system board supports the Bus Master DMA function, the option /DMA enables the Bus Master DMA function. The number xxx in hexadecimal form specifies the I/O port address (such as 1F0, 170, 1E8, or 168), and yy specifies the IRQ level (such as 14, 15, 11, or 10 in decimal). NOTE: If you are not familiar with I/O Port or IRQ level settings, do not implement/P: option. Refer to the README. TXT file for the latest driver installation updates. For Windows 95 and Windows NT Environment Windows 95 and Windows NT will automatically detect the new CD-ROM drive and load the appropriate device driver. However, there are times when Windows can not detect the CD-ROM drive. To install the drivers manually: 1. Click the Control Panel Icon in My Computer and then click Add New Hardware. [. . . ] 5. 6. 7. Table of Contents 4 Emergency-eject Option The Emergency-eject option allows the user to manually open the CD tray during a power malfunction. When the disc tray opens, pull out the tray and remove the disc from the CD-ROM drive. If your CD-ROM does not have an emergency-eject hole follow these steps: 1. When the disc tray opens, simply remove the disc from the CD-ROM drive. NOTE: Do not do this unless absolutely necessary. This procedure may damage the CD tray. ix 5 Jumper Settings This appendix explains the jumper settings on the drive and lists the pin configurations of each connector on the rear panel. [. . . ]