User manual AOPEN AX59PRO

[. . . ] AX59PRO User's Guide Printed in Taiwan PART NO. :49. 87801. 311 DOC. NO. :AX59P-1-E9903G AX59PRO Mainboard User's Guide Document Number Model and Revision Manual Revision Release Date : AX59P-1-E9809F : For AX59PRO revision 1. xx : English, revision F : Sep 21, 1998 More help for latest information: Taiwan USA http://www. aopen. com. tw http://www. aopen-usa. com http://www. aopenusa. com http://www. aopenamerica. com Europe http://www. aopen. nl Copyright Copyright © 1998 by this company. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, manual or otherwise, without the prior written permission of this company. ii Disclaimer This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". [. . . ] If enabled, AGP master will be disconnected if max retries are attempted without success. PCI#2 means AGP. 3-13 AWARD BIOS Chipset Features AGP Master 1 WS Write Enabled Disabled AGP Master 1 WS Write This item is used to enable or disable AGP master 1 wait state write. Chipset Features AGP Master 1 WS Read Enabled Disabled AGP Master 1 WS Read This item is used to enable or disable AGP master 1 wait state read. Chipset Features Video BIOS Cacheable Enabled Disabled Video BIOS Cacheable Allows the video BIOS to be cached to allow faster video performance. Chipset Features System BIOS Cacheable Enabled Disabled System BIOS Cacheable Enabling this item allows you to cache the system BIOS to further enhance system performance. Chipset Features Memory Hole At 15M-16M Enabled Disabled Memory Hole At 15M-16M This option lets you reserve system memory area for special ISA cards. The chipset accesses code/data of these areas from the ISA bus directly. Normally, these areas are reserved for memory mapped I/O card. 3-14 AWARD BIOS 3. 5 Power Management Setup The Power Management Setup screen enables you to control the mainboard's green features. See the following screen. Power Management Power Management Max Saving Mix Saving User Defined Disabled Mode Min Saving Max Saving Doze 1 hour 1 min Power Management This function allows you to set the default parameters of power-saving modes. Set to User Defined to choose your own parameters. Standby 1 hour 1 min Suspend 1 hour 1 min HDD Power Down 15 min 1 min 3-15 AWARD BIOS Power Management PM Controlled by APM Yes No PM Controlled by APM If "Max Saving" is selected, you can turn on this item, transfer power management control to APM (Advanced Power Management) and enhance power saving function. For example, stop CPU internal clock. Power Management Video Off Option Always On All Modes Off Suspend Off Susp, Standby Off Video Off Option To turn off video monitor at which power down mode. Power Management Power Button Override Enabled Disabled Power Button Override This is a specification of ACPI and supported by hardware. When Enabled, the soft power switch on the front panel can be used to control power On, Suspend and Off. If the switch is pressed less than 4 sec during power On, the system will go into Suspend mode. If the switch is pressed longer than 4 sec, the system will be turned Off. The default setting is Disabled, soft power switch is only used to control On and Off, there is no need to press 4 sec, and there is no Suspend. Power Management HDD Power Down Disabled 1 Min . . . . . 15 Min HDD Power Down This option lets you specify the IDE HDD idle time before the device enters the power down state. This item is independent from the power states previously described in this section (Standby and Suspend). 3-16 AWARD BIOS Power Management Doze Mode Disabled 1 Min 2 Min 4 Min 8 Min 12 Min 20 Min 30 Min 40 Min 1 Hour Doze Mode This item lets you set the period of time after which the system enters into Doze mode. The system activity (or event) is detected by monitoring the IRQ signals. Power Management Suspend Mode Disabled 1 Min 2 Min 4 Min 8 Min 12 Min 20 Min 30 Min 40 Min 1 Hour Suspend Mode This item lets you set the period of time after which the system enters into Suspend mode. The Suspend mode can be Power On Suspend or Suspend to Hard Drive, selected by "Suspend Mode Option". Power Management Power Management Power Management Power Management COM Ports Activity ON OFF VGA LPT & COM HDD & FDD DMA/Master To enable or disable the detection of COM port, LPT, HDD, VGA , and DMA activities for power down state transition. 3-17 AWARD BIOS Power Management Modem Wake Up Disabled Enabled Modem Wake Up This motherboard implements AOpen special circuit to detect modem ring signal and wakeup from soft power off. The most possible applications are automatic answering machine and fax send/receive. It does not like traditional green PC suspend mode, the system can be true power off, (identified by the fan of your power supply is off). You can use external box modem or AOpen MP56/F56 internal modem card for modem ring-on, but MP56/F56 is recommended, since MP56/F56 has special circuit to cooperate with this mainboard and the modem power and system power can be off together. Power Management RTC Wake Up Timer Enabled Disabled RTC Wake Up Timer This option lets you enable or disable the RTC Wake Up function. Power Management WakeUp Date (of Month) 0 1 . . . . . 31 WakeUp Date (of Month) This item is displayed when you enable the RTC Wake Up Timer option. For Example, setting to 15 will wake up the system on the 15th day of every month. Note: Setting this item to 0 will wake up the system on the specified time (which can be set in the WakeUp Time item) every day. Power Management WakeUp Time (hh:mm:ss) hh:mm:ss WakeUp Time (hh:mm:ss) This item is displayed when you enable the RTC Wake Up Timer option. Here you can specify what time you want to wake up the system. 3-18 AWARD BIOS Power Management Primary ON OFF Primary INTR This item is used to enable or disable the detection of IRQ3-15 or NMI interrupt events for power down state transition. Normally, this is applied to network card. Power Management IRQ [3-15], NMI Primary Secondary Disabled IRQ [3-15] Select Primary or Disabed option to enable or disable the detection of specified IRQ. [. . . ] You can copy this form and fax it to your distributor or send the form via e-mail. For getting better efficiency, we don't recommand you report the problem through phone. B-1 Troubleshooting No display. a. Check all jumper settings to make sure that you have set the proper jumpers, especially those for CPU type, single/dual voltage, CPU frequency and ratio. The simple way to identify power failure is to check the CPU fan and the power supply fan. [. . . ]