User manual AOPEN AX4SPEMAXII

[. . . ] Table of Contents Table of Contents 1. 1 A Thank-you Note Before You Get Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 2 Features of This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 3 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 2 Introduction to This Motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2. 1 How does your motherboard look like?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2. 2 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. 3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 3 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3. 1 Quick Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3. 2 Installation You Have to Know. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please be informed that this useful function only applies to advanced chassis; you may purchase an extra sensor, attach it on your chassis and make a good use of this function. Pin 1 32 Colored Coded Back Panel (for AX4SG Max II) The onboard I/O devices have PS/2 Keyboard, PS/2 Mouse, RJ-45 LAN Connector, COM1, VGA port, Printer, USB, AC'97 sound and game ports. The view angle of drawing shown here is from the back panel of the housing. SPP/EPP/ECP Parallel Port RJ45 10/100/1000 LAN Jack PS/2 Mouse Connector USB 2. 0 Line-In Speaker Out MIC-In PS/2 Keyboard Connector COM 1 Port VGA Port USB 2. 0 PS/2 Keyboard: PS/2 Mouse: USB Port: Parallel Port: COM1 Port: RJ-45 LAN Port: VGA Connector: Speaker Out: Line-In: MIC-In: For standard keyboard, which use a PS/2 plug. From Microphone 33 Colored Coded Back Panel (for AX4SPE Max II) The onboard I/O devices have PS/2 Keyboard, PS/2 Mouse, RJ-45 LAN Connector, COM1, COM2 port, Printer, USB, AC'97 sound and game ports. The view angle of drawing shown here is from the back panel of the housing. SPP/EPP/ECP Parallel Port RJ45 10/100/1000 LAN Jack PS/2 Mouse Connector USB 2. 0 Line-In Speaker Out MIC-In PS/2 Keyboard Connector COM 1 Port COM 2 Port USB 2. 0 PS/2 Keyboard: PS/2 Mouse: USB Port: Parallel Port: COM1 Port: COM2 Port: RJ-45 LAN Port: Speaker Out: Line-In: MIC-In: For standard keyboard, which use a PS/2 plug. From Microphone 34 LED Indication LED indication including Boot LED, Standby LED and AGP LED are AOpen's considerate designs that aim at providing you friendly system information. The STBY LED will light up when power is provided to the motherboard, giving you a convenient indication check the system power status in circumstances such as power on/off, stand-by mode and RAM power status during Suspend to RAM mode. BOOT LED will keep blinking when you power the system on and when your system is under POST (Power-On Self Test). After POST diagnoses everything all right and finishes the booting, the LED will stay on otherwise it will remain flashing to warn you that mistakes have occurred during POST AGP LED aims to protect your motherboard from being damaged by over voltage of AGP card. When AGP Protection Technology is implemented, this motherboard will automatically detect the voltage of AGP card and prevent your chipsets from being burnt out. Please note that if you install an AGP card with 3. 3V, which is not supported by Intel 865 chipset, the AGP LED on the motherboard will light up to warn you the possible damage of the exceeding voltage. AGP LED STBY LED BOOT LED 35 3. 4 Jumper Settings Allows you to turn off the voice from buzzer and JP2 Speaker Output speaker. Voice when it detects any error in operating system. JP14 Clear CMOS Jumper 1 1 Normal Clear CMOS (default) 1 Buzzer (default) JP2 Speaker Output Jumper 1 Speaker You can clear CMOS to restore system default setting. Voice provides four language versions: English, German, Japanese and Chinese. You can select your preferred language by JP15 & JP16 jumpers. 1 Disable (Default) 1 Enable JP28 KB/Mouse Wakeup Jumper JP15/16 Dr. Voice Languages Select Jumper English (Default) Chinese Pin1 Pin1 Pin1 Pin1 JP16 JP15 JP16 JP15 Japanese German JP28 Keyboard / Mouse Wakeup Jumper This motherboard provides PS2 keyboard / mouse wake-up function. 37 Chapter 4 Special Features and Utilities Chapter 4 Special Features and Utilities RAID (Redundant Array of Independent Disks) This motherboard supports RAID 0, RAID 1 and RAID 0+1 functions. For more RAID introduction, please visit our website: http://english. aopen. com. tw/tech/techinside/RAID. htm RAID Configuration Utility In order to make sure your system can recognize and operate Serial ATA RAID device smoothly, we have to enter RAID Configuration Utility to do some settings. After finishing the BIOS setup and reboot, you will see [Press CTRL + S to enter configuration Utility] about half way through the boot up. You will later be presented with a screen as shown below. Warning: The Serial ATA RAID function can be supported under Windows XP and Windows . Net environments. 38 Serial ATA RAID for Silicon Image 3114 Silicon Image's SATARaidTM provides Serial ATA RAID 0 (Striping), RAID 1 (Mirroring) and RAID 0+1 (Striping and Mirroring) functionality to enhance the industry's leading PCI-to-SATA host controller products. Standard with SATARaid software is a Graphical User Interface (GUI) that provides easy-to-use configurations for different RAID Sets supported. JAVA 2 Runtime Environment Installation The Java 2 Runtime Environment is required for the SATARaid GUI. The Java 2 Runtime Installer and executable package must be downloaded from the Sun Microsystems website at http://java. sun. com/j2se/downloads. html. The computer must have an Internet connection set up before installation can proceed. Save the installer file to a known location such as the My Documents folder. [. . . ] Without wizards or steps, all you have to do is to do one click and then it's done. After putting in the CD, you will be prompted with AOpen welcome page and our branches information. First, click on the install driver ICON at left side for necessary drivers. Second, click on the install utility ICON at left side for preferred utilities. [. . . ]