User manual AMX RDM-3EM6EM HEAVY DUTY ENERGY MANAGEMENT RELAY MODULES
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AMX RDM-3EM6EM HEAVY DUTY ENERGY MANAGEMENT RELAY MODULES. We hope that this AMX RDM-3EM6EM HEAVY DUTY ENERGY MANAGEMENT RELAY MODULES user guide will be useful to you.
Manual abstract: user guide AMX RDM-3EM6EM HEAVY DUTY ENERGY MANAGEMENT RELAY MODULES
Detailed instructions for use are in the User's Guide.
[. . . ] Installation Sheet
RDM-3EM and RDM-6EM Energy Management Modules
The RDM-3EM (FG606-81) and RDM-6EM (FG606-80) are 3 and 6 channel switching energy management modules. They are designed for use with the RDA series of enclosures in an AMX LightingTM system. [. . . ] Mounting points Control Port Strapping Jumpers (JP3 - JP4) Relays (1-6) Mounting points FIG. 2 RDM-3EM 5 Sequencing Delay Jumpers (JP1 and JP2) Mounting points
1 2 3 Relays (1-3)
1 2 3 4
RDM-3EM and RDM-6EM UL and C-Ul Ratings
· · · · · · · · · · · · · · · · · General purpose: 120, 240, 277, and 347* VAC, 20 A UL/CUL916 Energy Management Systems. Incandescent Fluorescent Transformer Low voltage General purpose All Class 1 wiring must be connected to proper terminals. For indoor use only.
6
Suggested Switched Loads
Control Port Strapping Jumpers (JP3 - JP7)
Sequencing Delay Jumpers (JP1 and JP2)
Caution: Pre-Installation Notes
Mounting points FIG. 1 RDM-6EM
Specifications
· · · · · · · · · Dimensions (HW): 10. 00" x 2. 75" (25. 40 cm x 6. 99 cm) Non-phase dependant Use wires rated at 75°C (167°F) Torque terminals to 4. 4 in lbs. Wire size: 26 AWG to 10 AWG Wire stripping length: 0. 28" (7 mm) Weight: 15 oz. (RDM-6EM) 4 mounting screws Control wiring harness
Included Accessories
*Agency approval pending
Jumper Information
Jumpers provide user-selectable configuration options on the Radia Energy Management Modules. Jumper Information
Sequencing Delay Jumpers (JP1 and JP2) The sequencing delay jumpers are set to short (0. 5 sec. ) delay by default. Installers can also select settings of no delay, medium delay (1. 0 sec. ) and long delay (1. 5 sec. ) between relays to minimize inrush current and stress on the electrical system. Installers have the option of setting multiple relays to an individual Radia port for large area control. For example, to combine A and B set JP3 to the ON position.
Connect the LINE IN and LOAD wiring on the (orange) 2-pin Channel connectors, as shown below:
LINE
LOAD
FIG. 5 2-pin Channel connectors
Control Port Strapping Jumpers (JP3 - JP7)
AMX Lighting Warranty Information
AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. [. . . ] AMX reserves the right to alter specifications without notice at any time. 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 · 800. 222. 0193 · fax 469. 624. 7153 · technical support 800. 932. 6993 · www. amx. com
93-0606-80
REV: A [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE AMX RDM-3EM6EM HEAVY DUTY ENERGY MANAGEMENT RELAY MODULES
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AMX RDM-3EM6EM HEAVY DUTY ENERGY MANAGEMENT RELAY MODULES will begin.