Detailed instructions for use are in the User's Guide.
[. . . ] Wallboxes: Lutron recommends using 3-1/2" (89mm) deep wallboxes for easier installation. Several controls may be installed in one multigang wallbox - see Multigang Installations (page 2). Remotes: Use only Lutron® HomeWorks Maestro Remote Dimmers (HD-RD) with HRD/HWD-6D, -6ND, -10D, -10ND, and -5NE controls. Use only Lutron HomeWorks Maestro Remote Switches (HD-RS) with HRD/HWD-8ANS controls. [. . . ] When making wire connections, follow the recommended strip lengths and combinations for the supplied wire connectors. Large:
Strip insulation 1/2" (13mm) for #10 AWG (6mm2), #12 AWG (4mm2) or #14 AWG (2. 5mm2). Strip insulation 5/8" (16mm) for #16 AWG (1. 5mm2) or #18 AWG (1. 0mm2). Use to join one or two #12 or 14 AWG supply wires with one #10, 12, 14, 16 or 18 AWG control wire. Large Wallbox Control Included: Wire Connectors (4)
Wallplate/Adapter purchased separately.
Mounting Diagram
Control Mounting Screws Wallplate Adapter Mounting Screws
3. Wire controls using Wiring Diagrams 1 and 2 (page 3).
When using power boosters or interfaces, use Wiring Diagrams 3, 4, and 5 (page 4). Up to nine HD-RD or HDRS remotes may be connected to the -6D, -6ND, -10D, 10ND, -5NE, or -8ANS controls.
Mounting Screws (2)
4. Push all wires back into the wallbox and loosely fasten
the control to the wallbox using the control mounting screws provided. Do not pinch the wires.
2
Wiring Diagram 1
Multi-Location Installation1 -6D, -10D with HD-RD
Remote Dimmer
Hot Black Red Black
Dimmer
Red Black
Remote Dimmer
Red
Lighting Load 120/127VAC 50/60Hz
Green Blue Green Blue Green Blue
Neutral
Wiring Diagram 2
Multi-Location Installation with Neutral1, 2 -6ND, -10ND, -5NE with HD-RD, -8ANS with HD-RS
Remote Dimmer/Switch
Hot Black Red Black
Remote Dimmer/Switch
Red Black
Dimmer/ Switch
Red
Lighting Load 120/127VAC 50/60Hz
Green Blue Green Blue Green Blue
White Neutral
1 Up to 9 HomeWorks® Maestro® Remote Dimmers/Switches may be connected to the HomeWorks Maestro Dimmer/Switch. Total Blue
wire length may be up to 250' (76m).
2 Remote Dimmers/Switches must be connected on the Line side of a multi-location installation when used with Neutral wire Dimmers or
Switches.
3
Wiring Diagram 3
Installation with Power Booster or ELV Interface1, 2
-6ND, -10ND with HD-RD
Hot/Live Black
Remote Dimmer
Red Black
Dimmer
Red
NGRX-PB or ELVI-1000
Lighting Load
DIM HOT OUT
CONTROL
120/127VAC 50/60 Hz
Green
Blue
Green
Blue
White Neutral
Wiring Diagram 4
Installation with Fluorescent Dimming Ballast Interface1, 2
-6ND, -10ND with HD-RD
Hot/Live Black
Remote Dimmer
Red Black
Dimmer
Red
FDBI-16A-120
Lutron® Hi-lume® Fluorescent Dimming Ballast(s)
CONTROL NEUTRAL SW HOT HOT IN
DIM HOT OUT
NEUTRAL
HOT IN
120/127VAC 50/60 Hz
Green
Blue
Green
Blue
Orange Black
White Neutral
White
Wiring Diagram 5
Installation with Neutral and Hi-Power Module1, 2
-6ND, -10ND with HD-RD -8ANS with HD-RS HP 2·4·6TM Hi-Power Module
N3
H3 DH3 SH3
N2
H2 DH2 SH2
N1
H1 DH1 SH1
N N H H DH 1 2 3
Lighting Load
Load Terminals
N1 H1 DH1 SH1
Control Terminals
N N H H DH 1 2 3
Remote Dimmer/Switch
Black Red
Dimmer/Switch
Black Red
Green Blue
Green Blue White
Hot/Live
Neutral
Neutral
Hot/Live
1 Up to 9 HomeWorks® Maestro® Remote Dimmers/Switches may be connected to the HomeWorks Maestro Dimmer/Switch. (76m).
2 Remote Dimmers/Switches must be connected on the Line side of a multi-location installation when used with Neutral wire Dimmers or
Switches.
4
120-277VAC 50/60 Hz
120/127VAC 50/60 Hz
Load Circuit
Control Circuit
Local Operation
Pressing the Tapswitch on any Dimmer, Switch, or Remote will alternately turn the lights ON and OFF. For HD-RD, the ON level will be the level previously set using the Dimming Rocker. Press and hold the top or bottom of the Dimming Rocker to raise or lower the light level. Double-tapping the Tapswitch on the HD-RD will turn the lights ON to full. Pressing and holding the Tapswitch for 1/2 second (while ON) activates a 10-second long fadeto-off.
Lamp Replacement
For routine lamp replacement, remove power from the fixture(s) by sliding the Front-Accessible Service Switch (FASS) to the OFF position (left). After replacing lamps, slide the FASS back to the ON position (right) to restore power. Danger - For any procedure other than routine lamp replacement, power must be disconnected at the main electrical panel.
Remote Dimmer Operation
Tapswitch Tap on/off
Dimming Rocker Press to Brighten Press to Dim FASSTM Front Accessible Service Switch
OFF
ON
Remote Switch Operation
Tapswitch Tap on/off
OFF
ON
FASS Front Accessible Service Switch
5
Troubleshooting Guide
Symptom
No lights at all
Cause and Action
Power not present · Circuit breaker OFF or tripped. Make sure the blue wires are not grounded or shorted to any other wires. Check wiring to be sure it agrees with installation instructions and wiring diagrams. Dioded lamps · If dioded lamps are being used, replace with non-dioded lamps. Check wiring to be sure it agrees with installation instructions and wiring diagrams. Check to see that tapswitches are not sticking for all control locations in the circuit.
Lights turn ON when tapswitch is pressed, then turn OFF
Light turns ON and OFF continuously
Load is less than minimum load requirement · Make sure the load connected to the dimmer or switch meets the appropriate minimum load requirement for that control. [. . . ] After the two year period, a pro-rated warranty applies to this product until eight years after the purchase. For more information regarding this warranty contact your Lutron representative. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. [. . . ]