User manual AMX AXB-DTMF+ DTMF INTERFACE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AMX AXB-DTMF+ DTMF INTERFACE. We hope that this AMX AXB-DTMF+ DTMF INTERFACE user guide will be useful to you.


AMX AXB-DTMF+ DTMF INTERFACE : Download the complete user guide (359 Ko)

Manual abstract: user guide AMX AXB-DTMF+ DTMF INTERFACE

Detailed instructions for use are in the User's Guide.

[. . . ] instruction manual AXB-DTMF+ DTMF+ Interface AXlink Bus Controllers AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series products are warranted for a period of one (1) year. Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year. Batteries and incandescent lamps are not covered under the warranty. This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer. [. . . ] Example: SEND_COMMAND DTMF, 'DIAL-9 W 214, 644-3048' Causes the AXB-DTMF+ to dial a 9 and then waits for dial tone before continuing to dial the next three digits. The AXB-DTMF+ pauses for the time specified in the Pause Send_Command before dialing the remaining six digits. Note: Tone length is set by the Tone Time Send_Command which sets the length of each generated tone and the time between tones. A pause can be added after a tone, for additional dial time, by using the Pause Send_Command. For more information refer to the 'TONE TIME-XXX ' and 'PAUSE-XXX ' Send_Commands. EXTEN-OFF Disable phones which are hanging off the extension phone connection on the AXB-DTMF+ by opening the phone circuit. Default at reset = NO Example: SEND_COMMAND DTMF, 'EXTEN-OFF' Disables phones that are hanging off the extension phone connection on the AXB-DTMF+ by opening the phone circuit. EXTEN-ON Enable phones that are hanging off the extension phone connection on the AXB-DTMF+ by closing the phone circuit. Default at reset = YES Example: SEND_COMMAND DTMF, 'EXTEN-ON' Enables any phones that are hanging off the extension phone connection on the AXB-DTMF+ by closing the phone circuit. FLASH Cause flash-hook for a period of time set by the Send_Command FLASH TIME. Example: SEND_COMMAND DTMF, 'FLASH' Causes flash-hook for a period of time set by the Send_Command FLASH TIME. Default at reset = NO Example: SEND_COMMAND DTMF, 'OFF HOOK' Places the AXB-DTMF+ off hook. AXB-DTMF+ DTMF+ Interface 9 Programming Operative System Send_Commands (Cont. ) Command ON HOOK Description Place AXB-DTMF+ on hook. Default at reset = YES Example: SEND_COMMAND DTMF, 'ON HOOK' Places the AXB-DTMF+ on hook. Timing System Send_Commands The following table lists the commands, which establish normal signal timing. Changing default time values may inadvertently alter the operation of the AXBDTMF+. It is unnecessary to change most default values. The commands are listed alphabetically by operation and include syntax, syntax descriptions, usage examples, time increments, and reset default values. Timing System Send_Commands Command BLOCKRDET-XXX Description For telephone lines with distinctive ring feature. Time increment = 10 ms Example: SEND_COMMAND DTMF, 'BLOCKRDET-185' Sets the time to ignore "sub rings " at 1. 85 seconds (1850 ms). FLASH TIME-XXX Set time AXB-DTMF+ will go "on-hook" when Send_Command FLASH is issued. · Time increment = 10 ms · Default at reset = 63 Example: SEND_COMMAND DTMF, 'FLASH TIME-65' Sets time AXB-DTMF+ will go "on-hook" when Send_Command FLASH is issued for . 65 seconds (650 ms). INROFFMIN-XXX Minimum time required for an incoming ring to be in the off state to reset ring count on AXB-DTMF+. · Time increment = 100 ms · Default at reset = 45 Example: SEND_COMMAND DTMF, 'INROFFMIN-55' Sets minimum off state time for an incoming ring to 5. 5 seconds (5500 ms). LOSSLCMAX-XXX The maximum time a loop current is off (used to detect other end hung up). · Time increment = 10 ms · Default at reset = 80 Example: SEND_COMMAND DTMF, 'LOSSLCMAX-90' Sets a . 9 second (900 ms) maximum off time for a loop current. 10 AXB-DTMF+ DTMF+ Interface Programming Timing System Send_Commands (Cont. ) Command LOSSLCMIN-XXX Description The minimum time a loop current is off (used to detect other end hung up). [. . . ] However, if this is not available, the DTMF+ is triggered by the receiver off-hook tone which occurs approximately 1 minute after call termination. Call Progress Reporting returned to the Axcess AXC-EM when a receiver off-hook is detected. 45 47 Distinctive Ring 41-44 Indicates time out while waiting for the dial tone during a wait (W) in the Dial Send_Command. The AXB-DTMF+ provides report capability for the type of ring received. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AMX AXB-DTMF+ DTMF INTERFACE




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AMX AXB-DTMF+ DTMF INTERFACE will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.