User manual AMPTRON 19 TFT LCD MONITOR

[. . . ] You can use the Plug and Play system without encountering usual installation problems. Your computer system can easily identify and automatically adjust the monitor. The LCD Monitor uses Display Data Channel (DDC) to send Extended Display Identification Data (EDID) to the computer system, so the computer system can be set to monitor auto adjust. 2 SAFETY Note: Please note the following safety precaution before using this monitor. English Electrical Sure the Voltage Electrical Shock Before connecting the AC power cord to the DC adapter socket, make sure that voltage of the DC adapter is suitable for local power. Do not insert any metal object into opening on the LCD monitor casing to prevent electrical shock. [. . . ] If the LCD monitor is not in use for a long time, please unplug it and restore it into the proper package, the original carton & packaging stuffs are preferred. The opening on the LCD Monitor casing is for the purpose of ventilation. To prevent overheating, the openings should not be blocked or covered. Do not place the LCD monitor on a bed, sofa, blanket or other soft surfaces; or else the soft objects will block the openings of the LCD monitors. If you place the LCD Monitor on a bookshelf or other airtight spaces, it's essential to leave a space of 4"(10cm) distance between the Monitor and the hard surface. Clean screen Ensure the area around the LCD monitor is clean and free of moisture. Please refer to [Maintenance] chapter for normal maintenance practice. 3 SET UP YOUR LCD MONITOR English Installation Notes Installation Position Note: Please read last section " Safety" before you install the LCD Monitor. Please note the instruction below prior to installing your LCD monitor. Choose a position where the reflection of light is minimal and away from a window for maximizing the quality of the screen image. It is important to keep 30 cm between the LCD monitor to minimize eyestrain. Workstation Height Angle of Vision Quick Installation Position the LCD monitor slightly above your horizontal vision as you are sitting. Tilt either forward or backward for the most comfortable viewing angle. After installation, please refer to "Auto Adjust" for automatic adjust procedures. Screen Adjustments Auto Adjust Though your computer system can identify the new LCD monitor system, the Auto Adjust function can be as to enhance the display. The LCD monitor will start the Auto Adjust process automatically for 10 consecutive seconds, where you will notice the image change as the Auto Adjust is working. Self Test Function Check (STFC): Your LCD monitor provides a STFC function, through which you can check whether the LCD monitor functions are working properly. If your LCD monitor is properly connected, but there is no image showing and the indicator light keeps orange, please follow the steps below to start STFC. If the image connector is disconnected or damaged, the image shown on following figure will also appear during normal operation. Turn off the LCD monitor and reconnect signal cable, and then turn the computer and LCD monitor on. If the LED of the LCD monitor is an orange color after completing the steps above, please check your VGA card and computer system. Your monitor should be operating properly. 4 OSD Control Keypad Button Definition Thanks to the user-friendly design of OSD (On Screen Display), you can adjust your monitor by the keypads in the front of the monitor. English 1 Power Switch LED 2 Auto / Exit 3 4 5 6 7 Turbo Input / Turbo (optional) / / Menu Speaker Power On/Off Power Indicator Blue: Normal Orange: Power Saving Off: Power Off Automatically optimize positions, phase & clock when OSD is not shown Exit the OSD menu when OSD is shown Quick brightness switching D-Sub, DVI input source selection Selection or adjustment when OSD is shown Quick brightness adjustment Adjustment when OSD is shown Quick contrast adjustment Enter OSD Access sub-menu & selection 5 Operate Explanation Your LCD has been adjusted to its optimal status before shipment. You can also adjust the image in accordance with the following illustrations and steps. English Press the "Menu" button to start the OSD feature. Click the "+" or "-" button to select the function to be adjusted. Click the "Menu" button to access into the function to be adjusted. Click the "+" or "-" button to change the current setting of the function. To exit the OSD menu or go back to the previous action by clicking the "Auto/Exit" button. [. . . ] Check to see if the LCD Monitor and accessories are damaged, broken, or strained. Avoid water or and liquid permeating into the LCD monitor or accessories. Do not use ketene (such as acetone), ethanol, toluene, acetic acid, methane, chloride, or abrasive detergent to clean the monitor because those chemicals can damage the LCD monitor. To clean your LCD monitor screen, use water or mild cleaner, as above, to gently moist a soft, clean cloth. [. . . ]