User manual AMERICAN DJ REVO RAVE

[. . . ] Revo RaveTM Introduction Unpacking: Thank you for purchasing the Revo RaveTM by American DJ®. Every Revo RaveTM has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact. [. . . ] It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. Figure 4 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion. 3-Pin XLR to 5-Pin XLR Conversion Conductor Ground/Shield Data Compliment (- signal) Data True (+ signal) Not Used Not Used 3-Pin XLR Female (Out) Pin 1 Pin 2 Pin 3 5-Pin XLR Male (In) Pin 1 Pin 2 Pin 3 Do Not Use Do Not Use ©American DJ Supply® - www. americandj. com - Revo RaveTM User Manual Page 6 Revo RaveTM System Menu Revo RaveTM System Menu System Menu: When making adjustments you can press ENTER to confirm your setup or you can wait 8 seconds for automatic setup. To exit without making any adjustments press the MENU button. ADDR - DMX Address Setting. 1. Tap the either the MENU, UP, or DOWN buttons until "ADDR" is displayed, press ENTER. Press ENTER to set your desired DMX address. SLND - This will let you set unit as a master or slave in a master/slave configuration. Either "MAST", "SL 1" or "SL 2" will be displayed. Tap the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim. NoTE: In a Master/Slave configuration you can set one fixture to Master and then set the next fixture to "SL 2", the fixtures will now have contrast movement to each other. SHND: SH 0 - 12 - Show modes 0-12 (Factory programs). Tap the MENU button until "SHND" is displayed, press ENTER. 2. "Sh X" will now be displayed, "X" representing a number between 0-10. Programs 1-12 are factory programs, while "Sh 0" is random mode. Press the UP or DOWN buttons to find your desired show and press the ENTER, then press and hold the MENU button for at least 3 seconds to confirm. ©American DJ Supply® - www. americandj. com - Revo RaveTM User Manual Page 7 ©American DJ Supply® - www. americandj. com - Revo RaveTM User Manual Page 8 Revo RaveTM System Menu Revo RaveTM System Menu SOUN - Sound Active mode. 1. Press the UP or DOWN buttons to select "ON" to activate sound active mode, or "OFF" to deactivate sound active mode. Press the ENTER, and then press and hold the MENU button for at least 3 seconds to confirm. for at least 3 seconds to confirm. TEST - This function will run a self test program. 1. The fixture will now run a self test. FHRS - With this function you can display the running time of the fixture. 7. on pages 5-7 as well as the set-up specifications that are included with your DMX controller. Use the controller's faders to control the various DMX fixture traits. For longer cable runs (more than a 100 feet) use a terminator on the last fixture. For help operating in DMX mode consult the manual included with your DMX controller. Sound Active Mode: This mode allows either single unit or several units linked together, to run to the beat of the music. Tap the MENU button until "SOUN" is displayed, and press Master-Slave Operation This function will allow you to link up to 16 ENTER. [. . . ] If the requested repairs or service (including parts replacement) are within the terms of this warranty, American DJ, Inc. will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it's original package. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. [. . . ]