User manual AMERICAN DJ Q-2422

[. . . ] Before the device is switched on, all fader and volume controls should be set to 0 or minimum position. Damages caused by manual modifications to the device or unauthorized operation by unqualified persons are not subject to warranty. For maintenance and/or service, contact an authorized American DJ® dealer. American DJ® AUDIO · Q-2422 User Instructions page 3 Operating Determinations When installing this mixer, please make sure that the device is not exposed to extreme heat, moisture or dust!Do not operate the mixer in extremely hot (more than 30° / 100°F) or extremely cold (less than 5°C / 40°F) surroundings. [. . . ] You can only control this signal after you have switched the PHONO / AUX SELECTOR SWITCH (29) on the rear panel to AUX, plus you must change the PHONO/AUX/LINE SWITCH (5) on the front panel to PHONO/AUX. The signal is then controlled via the CH1 and CH-2 faders (6). American DJ® AUDIO · Q-2422 User Instructions page 4 Functions (Front Panel) 15 22 5 4 3 21 2 20 24 16 1 19 10 18 6 17 8 7 9 13 11 12 14 23 (1) POWER SWITCH - Red LED will light when power is ON. (2) MASTER LEVEL - Dual LED's show the level of the left and right master output. (3) GAIN CONTROL - Used to set the level of the output signal for its designated channel. (4) BASS/MID/TREBLE CONTROL - Used to increase or decrease the LOW's, MID's, and HI's of the output signal. The Q-2422 features "Rotary Kills" with -35dB to +15dB output control. (5) PHONO/AUX/LINE SWITCH - Used to select the input to be sent to the individual channel. The selectors for AUX1/PHONO1 and AUX2/PHONO2 are on the rear panel (29). (7) CUE BUTTONS - Engage the CUE button to monitor the assigned channel. (8) FEATHER FADERTM CROSSFADER - Mixes the signals of the assigned channels. To assign channels use the ASSIGN SWITCH (17) located on either side of the crossfader. When the crossfader is set in the center position, both assigned channels can be heard at once. (9) ON/OFF "Q" START- Start and stop the CD Player with the slide of the fader. The ON/OFF "Q" START (9) switch activates this FADER "Q" START feature. When in the ON position, the FADER "Q" START allows the signal to return automatically to preset digital CUE POINTS on your American DJ CD Player* (* also featuring FADER "Q" START). For example, each time you slide the crossfader to far left, the CD Player will be triggered to play the song from the beginning of the preset CUE POINT. Refer to your American DJ CD Player User Manual for setting CUE POINTS. Turn the ON/OFF SWITCH (9) to the OFF position to disengage the "Q" Start function and resume to a normal fader. (10) TALKOVER SWITCH - While in the ON position the microphone can be used at any time, while this will not attenuate any other channels. When the switch is in the TALKOVER position, the microphone is hot, meaning that when the microphone is in use all channels attenuate -15dB except the MIC. When the microphone is not being spoken into all channels return to normal . In the OFF position, all signals return to their original level and the microphone is off. American DJ® AUDIO · Q-2422 User Instructions page 5 Functions (Front Panel) Cont. (11) CUE MIXING CONTROL - Mixes the signal to be monitored. [. . . ] (23) ZONE VOLUME, (24) ZONE BASS/TREBLE - Use ZONE VOLUME (23) and ZONE BASS & TREBLE (24) knobs to control the output signal for the ZONE. other rooms in a club, another amplifier, a satelite speaker system, a microphone paging system or the DJ control booth monitors). Inputs and Outputs (Rear Panel) 39 37 25 29 25 LIGHT CONTROL AUX 2 RIGHT BALANCED OUTPUT LEFT PHONO 2 AUX 1 PHONO 1 GND AC VOLTAGE SELECTOR AC INPUT 115/230V FUSE 0. 5A, F, 250V MASTER BOOTH REC LINE 4 LINE 3 LINE 2 GND PHONO 2 AUX 2 LINE 1 PHONO 1 AUX 1 L 115 MIC 2 MIC 1 R 1 2 PLAYER CONTROL OUTPUT CH-3 CH-2 CH-1 35 34 33 36 31 38 30 28 27 26 32 American DJ® AUDIO · Q-2422 User Instructions page 6 Inputs and Outputs Rear Panel) Cont. (25) GND (GROUND TERMINALS) - Connect the ground lead of the turntables with these terminals. There are two convenient ground terminals located on the rear of the mixer. (26), (27), (28) LINE / PHONO / AUX INPUT JACKS - Input jack for CH-1, CH-2, and CH-3. [. . . ]