User manual ALTEC LANSING DTS-215 LF SPEAKER SYSTEM

[. . . ] [PC] [DVI] [AV] [Component] [HDMI1] [HDMI2] [DisplayPort] [MagicInfo] [TV] Note · The [RGB/COMPONENT IN] port is compatible with RGB (PC) and Component signals. However, the picture may display abnormally if the connected external input signal is different from the selected video signal. · · MagicInfo can only be enabled when a network box is connected. A TV tuner box (sold separately) must be connected to use the TV. Introduction D. MENU button Opens the on-screen D. MENU. [. . . ] POWER S/W ON [ I ] / OFF Turns the network box on or off. Note · · See the "Connections" section for details about cable connections. The power switches of both of the monitor and the network box must be turned on for the network box to operate normally. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. POWER OFF Number Buttons DEL + VOL SOURCE D. MENU TOOLS Up-Down Left-Right buttons INFO The Color button and the PC/DVI/HDMI/DP selection button. TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P TV / GUIDE button Introduction MENU RETURN EXIT MagicInfo POWER OFF Number Buttons Turns the product On/Off. Used to enter the password during the OSD adjustment or to use MagicInfo. DEL / GUIDE button The "-" button is used to select Digital channels. Note This button can only be used in TV mode while a TV tuner box (sold separately) is connected. Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time. D. MENU DTV menu display Note This button can only be used in TV mode while a TV tuner box (sold separately) is connected. Up-Down Left-Right buttons INFO The Color button and the PC/DVI/HDMI/DP selection button. Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 4. Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Display . Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [L-AUDIO-R]] on the LCD Display . 2. Connections 3. 4. Press SOURCE on the product or remote control and select "AV". Then, start the Camcorders with a tape inserted. Note The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store. ) If your camcorder is stereo, you need to connect a set of two cables. Connecting Using a HDMI Cable 1. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] on the product and the HDMI output port on a digital device. Turn on the power switch. Connections Connecting to MAGICINFO OUT Connect the [MAGICINFO OUT] terminal of the network box and the [HDMI IN 2 (MAGICINFO)] terminal of the monitor using the HDMI cable. Connecting a LAN Cable Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC. Connections Connecting a USB devices You can connect USB devices such as a mouse or keyboard. Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. The figure shown below ("No Signal") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1920 x 1080. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. If the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. [. . . ] (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: A: "No signal" message. Ensure that the signal cable is firmly connected to the PC or video sources. [. . . ]