User manual ALTEC LANSING D91P MICROPHONE

[. . . ] Connect the [RGB/COMPONENT IN] port on the monitor to the COMPONENT port on the external device using the RGB to COMPONENT cable. Connect the [RGB/COMPONENT IN] port on the monitor to the BNC port on the PC using the RGB to BNC cable. · · DVI IN (PC Video Connection Terminal) Connect the [DVI IN] port on the monitor to the DVI port on the PC using the DVI cable. RGB/DVI/DP/HDMI AUDIO IN (PC/DVI/ DP/HDMI Audio Connection Terminal (Input)) Connect the [RGB/DVI/DP/HDMI AUDIO IN] terminal of the monitor and the speaker output terminal of your computer's sound card using a stereo cable (sold separately). DP IN Receives a signal from the Display port. Introduction Connect a DP cable to [DP IN] on the product and DP IN on another display. R] AV/COMPONENT AUDIO IN [L-AUDIO- Connect the [AV/COMPONENT AUDIO IN [L-AUDIO-R]] port on the monitor to the audio output port on the PC or on the external device using an audio cable. AV IN Connect the [AV IN] terminal of your monitor to the video output terminal of the external device using a VIDEO cable. AUDIO OUT Connect a headphone or an External speaker. DC OUT Make sure to use connecting [DC OUT] terminal to the authorized TV-Tuner Box [SBB_DTC/ZA]. Otherwise, this may result in damage to the product. HDMI IN 1 · Connect the [HDMI IN 1] terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable. Note The [HDMI IN 1] port can be connected to general external devices (DVD players, camcorders, etc. ) or the TV set-top box. · HDMI IN 2 (MAGICINFO) · Connect the [HDMI IN 2 (MAGICINFO)] terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable. Up to HDMI 1. 3 can be supported. · Introduction Note The MAGICINFO OUT port must be connected to the [HDMI IN 2 (MAGICINFO)] port. RJ 45 MDC (MDC PORT) MDC(Multiple Display Control) Program Port Connect the LAN cable to [RJ45 MDC] on the product and LAN on the PC. [. . . ] Directly selects an external input source: PC, DVI, HDMI or DP(DisplayPort). - Teletext Buttons SOURCE - This is activated when a TV tuner box is installed. MTS/DUAL MTSYou can select MTS (Multichannel Television Stereo) mode. Audio Type FM Stereo Mono Stereo SAP MTS/S_Mode Mono Mono Stereo Mono SAP Default Manual Change Mono DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. ENTER/PRE-CH This button is used to return to the immediately previous channel. The audio Introduction comes back on if MUTE or - VOL + is pressed in the Mute mode. MENU RETURN EXIT MagicInfo Opens the on-screen menu and exits from the menu or closes the adjustment menu. Note This button is disabled for products that do not support MagicInfo. Connections Connecting a Computer There are several ways to connect the computer to the monitor. · Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. · Connect the DVI Cable to the [DVI IN] port on the back of your LCD Display and the DVI port on the computer. Using the HDMI (Digital) connector on the video card. · Connect the [HDMI IN 1] port on the LCD Display to the HDMI port on the PC using the HDMI cable. Connections Note Select HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 as an input source when connected to the PC via an HDMI cable. Clean with a soft cloth after disconnecting the power cord. Troubleshooting · Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. (They may cause flaws or deformation of the screen surface. ) · The user is responsible for any damage caused by using these substances. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer. Check if the power cord and the video cables are properly connected to the computer. If you installed a new video card or if you assembled the PC, check if you installed the Adaptor(video). Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz. If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode, remove the Display Adaptor in the "Control Panel -> System -> Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver. Check List Note · The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. For more network-related information, refer to the MagicInfo Troubleshooting section. · Problems related to the Installation (PC Mode) Note Problems related to the LCD Display installation and their solutions are listed. [. . . ] If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Check the polarities (+/-) of the batteries. Troubleshooting A: A: A: A: Check if the batteries are empty. Check if a special fluorescent or neon lamp is on in the vicinity. Q&A Q: A: How can I change the frequency? [. . . ]