User manual ALTEC LANSING A7-MR994A VOTT SPEAKER SYSTEM

[. . . ] Steam Cycle This cycle sprays a small amount of water into the dryer drum after several minutes of tumbling with heat. It reduces bad odors from clothing that are difficult to remove when washing with water, and also reduces wrinkles. Sanitize Cycle This cycle sanitizes garments by infusing high temperature heat deep into the fabric during the drying cycle and eliminating 99. Use this cycle for clothing, bedding, towels, or other items needing sanitization. [. . . ] Go to Step 6 on the next page 01 installing your dryer installing your dryer _17 DV5471AEP-03022B-02_EN. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step 7) or 4 Wire system instructions (Step 8) below. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw of the terminal block. Insert the tab of the terminal block cover into your Dryer’s rear panel slot. If converting from a 4-wire electrical system to a 3-wire, you must connect the ground strap to the terminal block support to ground the dryer frame to the neutral conductor. Connect the ground wire (green or unwrapped) of the power cord to the external ground connector screw. If you want to connect B (Green or bare copper wire of power cord) to the Neutral Post without assembling with A (cabinet ground), call the service technician. Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block. Insert the tab of the terminal block cover into your Dryer’s rear panel slot. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. Attach the water hose to the other side of the “Y” connector. Using pliers, tighten the coupling with an additional two thirds turn. Indd Sec3:20 2012-01-02 10:28:35 Method2 - Using the Short Hose, Long Hose, and Y Connector The dryer must be connected to the cold water faucet using the new inlet hoses. If the “Y” connector cannot be attached directly to the cold water faucet, then you must use the short hose. If you have a washer water hose attached to the cold water faucet, unscrew and remove the hose. Using pliers, tighten the coupling with an additional two “Y’ connector thirds turn. Attach the ‘Y” connector to the stainless male end of the small hose. Using pliers, tighten the coupling with an additional two thirds turn. Attach the angled end of the long hose to the fill valve at the bottom of the dryer rear frame. Using pliers, tighten the coupling with an additional two thirds turn. Long hose 01 installing your dryer installing your dryer _21 DV5471AEP-03022B-02_EN. [. . . ] 0 °C) Cycle Temp control Normal Heavy Duty Perm Press Bedding Sensor Dry Towels (DV5471A*) Sanitize Delicates Wool Air Fluff (DV5471A*) Manual Dry Quick Dry Time Dry Steam Cycles Wrinkle Away Refresh High (Medium) High (No change) Medium (No change) High (No change) High (Medium) High (No change) Extra Low (No change) Low (No change) _ (No change) High (No change) High High (No change) High (No change) Sensor dry level Normal dry Normal dry Normal dry Normal dry Normal dry Very dry (No change) Normal dry Normal dry (No change) Time 42 min 58 min 32 min 50 min 50 min 60 min 34 min 28 min 20 min 30 min 40 min 20 min 15 min Drying Time 39 min 55 min 29 min 47 min 47 min 55 min 33 min 27 min 27 min 37 min 19 min 14 min Cooling Time 3 min 3 min 3 min 3 min 3 min 5 min 1 min 1 min 20 min 3 min 3 min 1 min 1 min 180 min Wrinkle prevent Time 36_ appendix DV5471AEP-03022B-02_EN. indd 36 2012-01-02 10:28:40 warranty ALTEC LANSING DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This ALTEC LANSING brand product , as supplied and distributed by ALTEC LANSING ELECTRONICS CANADA INC. , (ALTEC LANSING) and delivered new, in the original carton to the original consumer purchaser, is warranted by ALTEC LANSING against manufacturing defects in materials and workmanship for a limited warranty period of: 06 appendix One (1) Year All Parts and Labor This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the CANADA. To receive warranty service, the purchaser must contact ALTEC LANSING for problem determination and service procedures. [. . . ]