User manual ALTEC LANSING A7-8G VOTT SPEAKER SYSTEM

[. . . ] Steam cycle This cycle sprays a small amount of water into the dryer drum after several minutes of tumbling with heat. It reduces bad odors from clothing that are difficult to remove when washing with water, and also reduces wrinkles. Sanitize course This course allows you to sanitize garments by permeating high temperature heat deep into the fabric during the drying cycle. Use this cycle for clothing, bedding, towels, or other items needing sanitization. [. . . ] The electric service requirements can be found on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of the line is required. € If a power cord is used, the cord should be plugged into a 30-ampere receptacle. IMPORTANT: When local codes allow, the dryer electrical supply may be connected by means of a new power supply cord kit, marked for use with a dryer, that is U. 10 copper wire conductors terminated with closed loop terminals, open-end spade lugs with turned up ends, or with tinned leads. The power cord electric supply wiring must be retained at the dryer cabinet with a suitable UL-listed strain relief. € Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. ) Electric models – Canada Only • • A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or circuit breaker on both sides of the line is required. Indd Sec2:14 2011-03-28 ¿ÀÈÄ 3:42:01 CONNECTING THE INLET HOSE Method1 The dryer must be connected to the cold water faucet using the new inlet hoses. If space permits, attach the brass female end of the “Y” connector to the cold water faucet. Attach angled end of long hoses to fill the valve at the bottom of the dryer’s rear frame. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw of the terminal block. Insert the tab of the terminal block cover into your dryer’s rear panel slot. 9 cm) UL-listed strain relief If converting from a 4-wire electrical system to a 3-wire, the ground strap must be reconnected to the terminal block support to ground the dryer frame to the neutral conductor. Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw. Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block. Insert the tab of the terminal block cover into your dryer’s rear panel slot. With a level, check your dryer and make necessary adjustments to the leveling legs. At this time, make sure all gas connections (on gas models), exhaust and electrical connections are complete. (GAS MODELS ONLY- DV350AG*) The burner may not ignite initially due to air in the gas line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5 minutes. Indd Sec2:20 2011-03-28 ¿ÀÈÄ 3:42:06 operating Instructions, tips OVERVIEW OF THE CONTROL PANEL 02 Operating Instructions, Tips 1 2 3 4 5 6 7 8 9 1 Cycle Selector To select a cycle, rotate the Cycle Selector dial to the desired cycle. [. . . ] The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to maximize garment life and reduce laundering problems. Wash Cycle Normal Permanent Press / Wrinkle Resistant / Wrinkle Control Gentle/Delicates Hand Wash Water Temperature** Hot Warm Cold Bleach Any Bleach (when needed) Only Non-Chlorine (color-safe) Bleach (when needed) Tumble Dry Cycle Normal Permanent Press/ Wrinkle Resistant/ Wrinkle Control Gentle/ Delicates ** The dot symbols represent appropriate wash water temperatures for various items. The temperature range for Hot is 105° –125° F/ 41° – 52° C, for Warm 85° – 105° F/29° – 41° C and for Cold 60° – 85° F/16° – 29° C. [. . . ]