User manual ALTEC LANSING 9813 SPEAKER SYSTEM

[. . . ] Indd 1 2012-04-04 12:12:25 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. GENERAL ERROR FUNCTION NO Error Code (Diagnostic Code Error Image) dc dS Description An unbalanced load that prevents your washer from spinning. Corrective Action Redistribute the load, press the Start/ Pause button. Press the Power button to turn off your washer, then turn it on again. [. . . ] To exit the Cycle Count Check Mode, press the “Signal” key again. s/W Version Check Mode Definition of S/W Version Check Mode: Service Mode WF455AR* : Soil Level WF457AR* : 4 Key S/W Version Check Mode - S/W Version Check Mode is to bring up S/W Version information. How to Enter: Model : WF455AR* - To enter the S/W Version Check Mode, press the Soil Level Key during Service Mode. Press the Soil Level Key to bring up its software Version EX) Generate dE49 at Version 49 (dE is Micom code, 49 is it’s software version) 3. To exit the S/W Version Check Mode, press the Soil Level S/W once again. Indd 10 2012-04-04 12:12:28 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. Fast Time Down Test Mode Service Mode WF455AR* : Temp WF457AR* : 1 Key Fast Time Down Test Mode Definition of Fast Time Down Test Mode: - Fast Time Down Test Mode is to forward the program to the next cycle stage. How to Enter: Model : WF455AR* - To enter the Fast Time Down Test Mode, press the Temp key during Service Mode. Each stage is located at key points of a complete cycle as follows: - End of Each Fill (Beginning of Wash or Rinse Tumble Session) Caution: Check if the current water level is higher than the Reset water level and then perform the Fast time down test. - Beginning of Drain Session - Beginning of Spin Session (Here , it checks the water level. So, if it is over the reset level, it carries out draining before the spinning. - If the Start/Pause button is pressed in WASH Mode, the door is locked (door Lock) and the motor rotates left and right at 45 RPM in a 7 sec on and 3-sec off cycle. After the five (5) minutes have elapsed, back to the initial Demo mode-Wash Mode. - If the Start/Pause button is pressed during a WASH mode operation, back to the initial Demo mode-Wash Mode. Connecting to a hidden AP (WF457AR*) Proposed hidden AP specifications - The product can only connect to a hidden AP when it is in Shop Demo Mode. - After the connection is established, even if the connection is disconnected because the product is unplugged or the AP is turned off, the connection is automatically restored when the product is plugged in again or the AP is turned on. - AP name: The full name is displayed in the same way as an existing AP. Enter Shop Demo Mode (Tap 1  2  1  2  1) The Hidden AP button appears in the Network menu. Indd 15 2012-04-04 12:12:29 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. eEPROM Clear Check Definition of EEPROM Clear Mode: - EEPROM initialization. - All course/option settings are to be reset to default values after EEPROM initialization. - When Service arises and it needs PCB replacement, EEPROM should be reset. [. . . ] (Refer to PCB Connector Check) Wrong Water Temperature • Check if both of the water taps are fully open. € Make sure the domestic water heater is set to deliver water lower than 120°F (49°C) hot water at the tap. € If the water heater is located far from the washer, screw out the hot water tap and let its water pass until you get hot water. € Too Hot/Too Cold: Reduced amount of water is supplied while PCB controls the influx to regulate the actual temperature of the water in the tub. [. . . ]