User manual ALTEC LANSING 95-BK SPEAKER SYSTEM

[. . . ] - Upon entry into Service Mode, the Sensor Bar Touch Data will be shown (Default Service Mode). How to Enter: - To enter Service Mode, press Wrinkle Prevent and Temp Keys for 3 seconds, until it sends out a beeping sound. - If pressing Wrinkle Prevent + Temp Keys for 3 seconds in Service mode , it will return Normal mode. - Even though entering Service mode, the operating cycle will not be influenced. [. . . ] - Even though entering Service mode, the operating cycle will not be influenced. Sensor Bar Touch Data Mode Definition of Sensor Bar Touch Data Mode: - This action will put the dryer into sensor bar touch data mode - Dryer will display Sensor Bar data. This mode is default mode of entering service mode How to Enter: - With Power On pressing Wrinkle Prevent and Temp Keys for 3 seconds Cycle Count Mode Definition of Cycle Count Mode: - This mode is to bring up the total number of cycles that User have carried out. How to Enter: - To enter cycle count mode press the Wrinkle Prevent in Service Mode. Software Version Mode Definition of Software Version Mode: - It is to retrieve its software version How to Enter: - At Service Mode, press Temp until it sends out a beeping sound ex) In case of “U0 05”, U0 means major version “U0” 05 means minor version “05” - If press Temp key In Software Version Mode, it will return Service Mode. Indd 3 2012-04-21 �� 10:01:26 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Data Display Mode Definition of Data Display Mode: - Display Mode 1 : Temperature data(Celsius) - Display Mode 2 : Average Touch Sensor data for 1 minute - Display Mode 3 : Average Temperature(Celsius) data for 1minute How to Enter: - With Power On, press AdjustUp Key + AdjsutDown Key for 7 seconds until it sends out a beeping sound . - If not pressed any keys for 5 minutes, it will be set back from Data Display Mode - If pressing AdjustUp Key in this mode, Display Mode will be increased. - System Check Mode(t2 mode) Progress Function Performed Start/Pause Motor(CW) Relay On  Heater Relay On  Heater Relay Off, Motor(CW) Relay Off How to Enter: - While in Power Off, pressing the Dry Level + Power keys simultaneously will put the dryer into the System Check mode 4 Technical_information-03044A-02_EN. Indd 4 2012-04-21 �� 10:01:26 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. €¢ Clothes too wet due to insufficient spin out by washer. • Thumping Check for loose tumbler baffle , rear tumbler roller(s) worn or misaligned , out-of-round tumbler or high weld seam on tumbler. €¢ Ticking Check for loose wire harness or object caught in blower wheel area. Noisy and/Or 12 • Scraping Check for front or rear bulkhead felt seal out of Vibration position or worn tumbler front bearings. Indd 7 2012-04-21 �� 10:01:26 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Indd 8 2012-04-21 �� 10:01:27 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Indd 9 2012-04-21 �� 10:01:28 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Approx ∞ Ω without laundry Approx 190Ω ± 10% with wet clothes Cycling Thermostat - Disconnect harness and test Blue wire Pin 3 to Red wire Pin 6. approx 10 KΩ at 25 °C/77 °F 10 Technical_information-03044A-02_EN. Indd 10 2012-04-21 �� 10:01:28 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. [. . . ] approx 10 KΩ at 25 °C/77 °F 10 Technical_information-03044A-02_EN. Indd 10 2012-04-21 �� 10:01:28 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. External ground connector Neutral grounding wire (green/yellow) Center silver-colored terminal block screw Neutral wire (white or center wire) ¾” (1. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw of the terminal block. [. . . ]