User manual ALTEC LANSING 817A LF SPEAKER CABINET

[. . . ] # Infrared sensor window Receives the infrared wave from the remote control. Used for MENU setup. TV/VIDEO TV/VIDEO 3 6 9 Volume up/down buttons / Adjusts the volume. Audio input terminals (AV-2) Connects to a camcorder, video game, etc. Headphone jack Use to listen to the audio with headphone. [ Behind the door ] Using headphone Insert headphone plug into headphone jack to listen to audio with headphone. [. . . ] If "5-" is indicated, press to select one-digit input, 5 and then press again. · To select a two-digit channel, such as 15, press 1 to select the two-digit input. Press , and then 5 press . Installing batteries in the remote control unit -115 SECAM D/K a With your thumbnail, pull up at the slit to open the battery cover. b Insert two batteries (size AA). c Replace the battery cover. Adjusting volume !Adjust volume using / . · The volume bar disappears approximately three seconds after the volume has been adjusted. VOLUME 10 · Channels that have been skipped cannot be selected by CH / CH . · The AV1 (or COMPONENT), AV2 input channels cannot be selected using Use TV/VIDEO to select these channel. CH / CH on the remote control. E7 PRESETTING CHANNELS E8 SETTING AND ADJUSTMENT Auto channel tuning Automatically tunes in and presets receivable TV stations. Channel setting Enables individual channel setting. AUTO(D/K) VHF 1 48. 25MHz !again to display AUTO mode screen. changes the screen as shown below. MANUAL Normal screen AUTO !/ / CH MENU PICTURE SOUND FEATURE TIMER CH-SETTING CH :SELECT :ENTER TV/VIDEO MENU/PRESET CH to select "CH-SETTING". to display CH-SETTING 1 4 7 2 5 8 0 3 6 9 · Pressing Language MENU/PRESET CH CH MENU:RETURN # Press / on TV set. 1 [ Behind the door ] menu. CH CH MENU · All the TV stations in your area that can be received by the TV set are automatically preset between channels 1 to 99. · The screen shows whatever is on channel 1 when auto channel preset is finished. $ Press CH-SETTING CH / CH to select desired setting. % Each time you press MENU/PRESET / , setting for individual items changes as follows: POSITION COLOUR SOUND SKIP FINE CH :SELECT :ADJUST CH27 AUTO D/K OFF 168. 25MHz MENU SURROUND LANGUAGE NORMAL MENU:RETURN TV · POSITION The channel position changes to the higher or lower number. · COLOUR AUTO TV/VIDEO Manual channel tuning Enables manual channel tuning to a desired TV station. 1 4 2 5 8 0 PAL SECAM N443 3 6 9 !twice to display MANUAL mode changes the screen as shown below. MANUAL Normal screen MANUAL(D/K) VHF 1 48. 25MHz 7 Number buttons · SOUND B/G I D/K CH MENU/PRESET CH CH MENU CH screen. · Pressing Language MENU/PRESET SURROUND LANGUAGE NORMAL MENU · SKIP ON OFF Channel numbers with a " " mark on the left are set to SKIP. This is useful for timer cooking while you watch TV. Channel / Timer display Displays the current channel number, the timer, and other settings on the screen. !Press . TV/VIDEO TIMER OFF ON POSITION VOLUME --:---:---:-1 4 2 5 8 0 TV/VIDEO / / CH to select " ". to set time. 3 6 9 CH CH 7 TIMER OFF ON POSITION VOLUME --:---:-1:50 · Maximum time that can be preset is 12 hours and 50 minutes. · The right example shows that the Reminder will be activated after one hour 50 minutes. CH CH MENU · The time remaining on the Off timer, On timer, and Reminder appears on the screen. · When no timer is set, the channel number, colour and sound system appear on the screen. · Press again to clear these current settings display on the screen. TV/VIDEO 1 4 2 5 8 0 3 6 9 OFF ON 2:30 8:00 1:50 7 Number buttons CH CH MENU SECAM D/K LANGUAGE 5 SURROUND NORMAL MENU SURROUND LANGUAGE NORMAL @ Press again, the channel number, colour and sound system appear on the screen. TV $ Press MENU until normal screen appears. TV 0:05 0:04 0:03 0:02 0:01 0:00 · Five minutes before the preset length of time expires (in the example, after one hour and 45 minutes) and each minute thereafter, the remaining time appears on the screen for several seconds. · When the preset length of time has passed, " 0:00" flashes in red. Mute Silences the sound. !Press . " appears on the screen, and the sound · Press , " is silenced. Flashing @ Press level. , the volume returns to its previous is pressed at any time. E10 FEATURES · Mute will be cancelled if the Blue screen Automatically turns the screen blue if a broadcast signal is not received. Channel recall Switches back to the channel you were watching just before the current channel. MENU PICTURE SOUND FEATURE TIMER CH-SETTING CH :SELECT :ENTER !Press @ Press # Press $ Press % Press No signal MENU CH to call MENU screen. / / / CH Press . SECAM 5 to select "FEATURE". to select "BLUE BACK" to "ON" or "OFF". · The channel previously viewed returns to the screen. SECAM 7 MENU:RETURN MENU until normal screen appears. Blue screen TV off (Indicator) FEATURE BLUE BACK ON Example: After switching from channel 5 to channel 7, the channel will change to channel 5. [. . . ] ON : Setting to this mode during stereo signal reception produces a spacious sound, making the most of the speakers' performance. : Setting to this mode during monaural signal reception creates monaural sound that is similar to stereophonic sound. SURROUND OFF 7 CH CH MENU SURROUND LANGUAGE NORMAL SURROUND Sound OK, picture poor. Picture rolls vertically. TV Picture OK, sound poor. Picture lines or streaks. SURROUND ON Remote control does not work. Problems ON E12 CONNECTIONS Possible Causes/Remedies Try a new channel to check for possible station trouble. If outside antenna is used, check for broken wires. Connecting to video equipment Enjoy playback from a video disc player, VCR or other video equipment by connecting them to this TV set using the Audio/Video in terminals. Example use of front terminals Example use of rear terminals For Playback TV Yellow : To VIDEO White : To AUDIO (L) Red : To AUDIO (R) TV VCR DVD Player Video Game To Audio/ Video out terminals Y Check for local interference. [. . . ]