User manual ALTEC LANSING 807-8A HF DRIVERS

[. . . ] Quest'apparecchio è conforme ai requisiti delle direttiva 1999/5/CE. Este equipamento obedece às exigências da directiva 1999/5/CE. Tämä laite täyttää direktiivi 1999/5/EY. This equipment has been tested according to the pan-European TBR 21 regulation. It will operate on all analogue telephone networks which comply with the TBR 21. [. . . ] If a document icon ( ) appears to the right of a memory box key, document data has been stored in that box and you can print it out. However, the contents cannot be printed or deleted while the memory box is being used for transmission. DATA MARKETING GROUP ALTEC LANSING BRANCH EX C PUBLI PROCEDURE FOR F-CODE POLLING Make sure that a document has not been loaded in the auto document feeder or on the document glass, and then follow the steps below. NOTES G You must know the sub-address (SEP) and passcode (PWD) of the other machine's F-code polling memory box. G Serial polling (selecting multiple fax machines to be polled using a group key or by touching the [NEXT ADDRESS] key) is not possible with F-code polling. 4 1 In fax mode, touch the [SPECIAL MODES] key and then the key. MODE SWITCH ADDRESS REVIEW SPECIAL MODES SUB ADDRESS FILE TO RECEPTION MEMORY:100% fax number, sub-address, 3 Enter the of the other fax machine. and passcode To use a one-touch key, touch the [ADDRESS BOOK] key to display CORPO. TPS the address book. ALTEC LANSING GROUP Refer to steps 2 through 5 on page 4-3 for the procedure for entering sub-addresses and passcodes. SPE QUICK FILE If the address book screen appears, touch the [CONDITION SETTINGS] key to display the condition settings screen (page 15). 2 Touch the [POLLING] key and then touch the [OK] key. POLLING SPEAKER 4 Press the [START] key. "POLLING. " appears on the screen. After communicating with the other machine, your machine prints the received document data. The [POLLING] key is highlighted and the polling icon appears. OK To cancel polling, touch the [POLLING] key once again to cancel the POLLING selection. You will return to the initial screen. RESEND NOTES G Cancelling a transmission Press the [JOB STATUS] and cancel the transmission in the same way as when cancelling a stored transmission. (See "CANCELLING A FAX TRANSMISSION"on page 2-8) G Only one F-code polling timer operation can be stored (see page 3-6). 4-5 F-CODE CONFIDENTIAL TRANSMISSION F-Code confidential transmission provides a secure means of faxing confidential documents. The sub-address and passcode programmed in the memory box restrict the recipients of the fax, and once received in the memory box, the fax can only be printed by someone who knows the print passcode (PRINT PIN. The relay machine and the originating machine that requests the relay transmission must both support F-codes; however, the end receiving machines programmed in the F-code relay broadcast memory box do not need to support F-codes. Relay request machine (sends document) 1) Document is sent from machine requesting relay transmission Sub-address Relay machine (your machine) 2) Check sub-address and passcode Does not match Passcode S. F. 3) Document data is read into relay broadcast memory box (reception is permitted). 4) Document is successively transmitted to end receiving machines programmed in the relay broadcast memory box. Receiving machine A Receiving machine B Receiving machine C The machine that originally sends the document is called the relay request machine, and the machine that has a memory box containing the end receiving machines and which relays the received document to those machines is called the relay machine. The relay machine also prints the document sent by the relay request machine. For example, corporate headquarters in Seattle wants to send the same document to branch offices in San Francisco, Oakland, Berkeley, and San Jose. If the San Francisco office creates a relay broadcast memory box and programs the Oakland, Berkeley, and San Jose offices as end receiving destinations, the overall phone charges will be lower than if the Seattle office uses the normal broadcast transmission function (page 3-2). This function can also be combined with a timer setting (page 3-6) to take advantage of off-peak rates, allowing a further reduction in phone charges. Transmission by the relay machine is called "F-code relay broadcast transmission", and transmission from the relay request machine to the relay machine is called "relay request transmission". NOTES G This machine does not support Sharp's previous relay broadcast function, which uses the programmed sender's number and relay ID code. G To create an F-code relay broadcast memory box and program, edit, and delete end receiving machines, refer to pages 6-10 to 6-14. G The relay request machine only bears the expense of sending the document to the relay machine. The relay machine bears the expense of sending the document to each of the end receiving machines. 4-8 Match F-CODE RELAY BROADCAST TRANSMISSION USING THE F-CODE RELAY BROADCAST FUNCTION (your machine is the relay machine) When a document is received from a relay request machine, the F-code relay broadcast function transmits the document to the end receiving machines using a memory box only if the sub-address and passcode sent by the relay request machine are correct. Refer to pages 6-10 through 6-14 for the procedures for creating, editing, and deleting memory boxes. [. . . ] 4-3 -Image rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 -PC-fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18 -Priority transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 -Quick On-line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]