User manual ALTEC LANSING 806A HF DRIVERS

[. . . ] Micro sistemi 806A HF DRIVERS composto da 806A HF DRIVERS (apparecchio principale) e CP-MP40H (sistema di diffusori). 806A HF DRIVERS micro systeem bestaande uit 806A HF DRIVERS (hoofdtoestel) en CP-MP40H (luidsprekersysteem). 806A HF DRIVERS Sistema de Micro Componente composto de XLMP50H (unidade principal) e CP-MP40H (sistema de alto-falante). 806A HF DRIVERS Micro Component System consisting of 806A HF DRIVERS (main unit) and CP-MP40H (speaker system). DEUTSCH Siehe Seiten i bis x und D-1 bis D-32. [. . . ] If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the centre, along the radius. NO YES Correct General Information The sound level at a given volume setting depends on speaker efficiency, location, and various other factors. Do not turn the volume on to full at switch on and listen to music at moderate levels. 8 E-2 05/3/24 806A HF DRIVERS(H)E1. fm TINSZA054SJZZ 806A HF DRIVERS Controls and indicators 1 2 3 4 5 6 7 10 11 12 13 14 Reference page 1. Disc Track Down or Fast Reverse, Tape Rewind, Tuner Preset Down Button . Disc Track Up or Fast Forward, Tape Fast Forward, Tuner Preset Up Button . 25, 26 ENGLISH General Information 8 15 9 17 18 19 20 16 16. 6, 7 E-3 05/3/24 806A HF DRIVERS(H)E1. fm TINSZA054SJZZ 806A HF DRIVERS ENGLISH 5 1 2 3 4 6 7 8 9 10 11 12 13 14 15 15. 17 8 17 E-4 05/3/24 806A HF DRIVERS(H)E1. fm TINSZA054SJZZ 806A HF DRIVERS Controls and indicators (continued) 1 16 2 3 4 17 18 19 20 21 22 23 24 25 26 27 28 Reference page 1. 23 ENGLISH General Information 5 6 7 8 9 10 11 12 13 14 15 E-5 05/3/24 806A HF DRIVERS(H)E1. fm TINSZA054SJZZ System connections !Aerial connection Make sure to unplug the AC power lead before making any connections. AM loop aerial 806A HF DRIVERS ENGLISH Supplied FM aerial: Connect the FM aerial wire to the FM 75 OHMS socket and position the FM aerial wire in the direction where the strongest signal can be received. Supplied AM loop aerial: Connect the AM loop aerial to the LOOP socket. Point the remote control directly at the remote sensor on the unit. ALTEC LANSING TINSZA054SJZZ (H) 8 E-8 05/3/24 806A HF DRIVERS(H)E1. fm TINSZA054SJZZ 806A HF DRIVERS Sound control !Adjusting the volume Main unit operation: When the VOLUME control is turned clockwise, the volume will increase. Remote control operation: Press the VOLUME (- or +) button to increase or decrease the volume. ENGLISH 01 2 . . . . . Adjusting the bass Basic Operation Main unit operation: 1 Press the BASS/TREBLE button to select "BASS". Remote control operation: 1 Press the BASS/TREBLE button to select "BASS". 2 Within 5 seconds, press the VOLUME (- or +) button to adjust the bass. -3 . . . 0 . . . 4 !Adjusting the treble Main unit operation: 1 Press the BASS/TREBLE button to select "TRE". Remote control operation: 1 Press the BASS/TREBLE button to select "TRE". 2 Within 5 seconds, press the VOLUME (- or +) button to adjust the treble. -3 . . . 0 . . . 4 E-9 05/3/24 806A HF DRIVERS(H)E1. fm TINSZA054SJZZ Setting the clock 3 Within 1 minute, press the PRESET ( or ) button to adjust the hour, then press the SHIFT button and then the MEMORY button. 806A HF DRIVERS ENGLISH Press the PRESET ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. 4 Within 1 minute, press the PRESET ( or ) button to adjust the minutes, then press the SHIFT button and then the MEMORY button. This may be operated only with the remote control. In this example, the clock is set for the 24-hour (0:00) display. 1 Press the SHIFT button and then the CLOCK button. [. . . ] " Has condensation formed inside the unit? Possible cause " Is the erase-prevention tab removed?" If a power failure occurs during playback, the heads remain engaged with the tape. " Does the remote control sensor receive strong light? References 8 E-30 05/3/24 806A HF DRIVERS(H)E3. fm TINSZA054SJZZ 806A HF DRIVERS Troubleshooting chart (continued) !If trouble occurs When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc. ) or if it is operated incorrectly, it may malfunction. [. . . ]