User manual ALTEC LANSING 604-8K DUPLEX SPEAKER

[. . . ] 4 Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 OSD (On-Screen Display) Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 · Full Auto Channel Preset (AUTO) · Manual Channel Preset (MANUAL) Fine Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Flashback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 3 2 1 . . . Changing channels using the CHANNEL SELECT buttons on the remote control · To handle the increasing number of channels available, this TV set allows you to select up to 100 position (Channel 0 to 99). Follow the procedure shown below to select channels. 1 4 7 2 5 8 0 3 6 9 CH CH To select a one-digit channel (e. g. , Channel 5): (1) Press the 5 button. (2) If "5-" is indicated and the picture does not change, press the button to switch over to the 1-digit select mode and press the 5 button again. PAL B/G 5 1 4 7 2 5 8 3 6 9 0 CH CH To select a two-digit channel (e. g. , Channel 15): (1) Press the button to set the 2-digit select mode. (3) Press the 5 button. · In this mode entering a 0 first will enable selection of single digit channels e. g. · Complete this procedure within 6 seconds, otherwise the selection will not be made. -115 PAL B/G (3) Adjusting the Volume CH CH Press the VOLUME UP ( ) or DOWN ( ) button to adjust the volume. The number of oval blocks " indicates volume level. " (TV set) The display disappears approximately 3 seconds after the volume adjustment has been completed. VOLUME 7 OSD (On-Screen Display) Language Selection On-Screen Display language selection 1 4 7 2 5 8 0 3 6 9 !Press the FUNCTION button 5 times. @ Press the CHANNEL UP (CH) or DOWN (CH) button to move the : mark on the screen when selecting "ENGLISH", "CHINESE", "FRENCH", "MALAY" or "ARABIC". ENGLISH FRANCAIS BAHASA MELAYU CH CH @ !, # FUNCTION SYSTEM TIMER NORMAL PICTURE # Press the FUNCTION button again. The on-screen display disappears. · If approximately 6 seconds pass without a button being pressed, the mode setting is automatically terminated and the TV set returns to normal mode. Presetting Channels Full Auto Channel Preset (AUTO): Automatically tunes in and presets receivable TV stations. (TV set) !Press the PICTURE (PRESET- 1 ) button on the TV set for more than 2 seconds, to turn on Full Auto Channel Preset Mode. Sound System AUTO(B/G) VHF 1 48. 25MHz ! @ @ Press the VOLUME UP ( ) ) button on the or DOWN ( TV set. All the TV stations in your area that can be received by the TV set are automatically preset between channels 1 to 99. finished, the screen shows whatever is on channel 1. · Unused channels are automatically skipped. # When full auto channel preset is PAL B/G 1 8 ENGLISH Presetting Channels (continued) Manual Channel Preset (MANUAL): Setting a channel to a desired TV station. (TV set) !After completion of above steps, the TV set returns to Standby mode automatically. (If you press any key before the TV set returns to Standby mode, the TV set remains on and does not return to Standby mode. ) (Example) Flashing Turns red for 1 minute. Flashing · · · · To cancel the Reminder, press the NORMAL button during the Reminder mode. The Reminder is cancelled if the Ï POWER switch on the TV set is turned off or if the power is otherwise cut off. If approximately 6 seconds pass without a button being pressed, the mode setting is automatically terminated and the TV set returns to normal mode. 13 Timers (continued) OFF Timer: Automatically turns to Standby mode after the set length of time has passed. Press the TIMER button 2 times and the OFF display appears. 1 4 7 2 5 8 0 3 6 9 @ CH CH @ Press the VOLUME UP ( ) or DOWN ( ) button to set the time. (Maximum time that can be preset is 12 hours and 50 minutes. ) In this state, the Timer starts to count down. !, # FUNCTION SYSTEM TIMER NORMAL PICTURE TV # When you have finished setting the time, press the TIMER button 2 times. The on-screen display disappears. H Action of the Off Timer 5 minutes before the Off Timer activates, the remaining time is displayed on the screen for 3 seconds, and reappears at the start of every remaining minute. A flashing display of the remaining time appears on the screen during the last five seconds before the Off Timer activates. When the preset length of time (in the above example, 2 hours and 30 minutes) has passed, the TV set enters Standby mode. Flashing for 5 seconds (The power turns off) · To cancel the Off Timer, press the NORMAL button during the Off Timer mode. · The Off Timer is cancelled if the power is turned off with the STANDBY/ON (ø) button on the remote control or the Ï POWER switch on the TV set or if the power is otherwise cut off. · If approximately 6 seconds pass without a button being pressed, the mode setting is automatically terminated and the TV set returns to normal mode. 14 ENGLISH Timers (continued) ON Timer: Automatically turns power on after the set length of time has passed. [. . . ] COLOUR SYSTEM mode changes as shown on the right each time you press the VOLUME UP ( ) or DOWN ( ) button. TV/VIDEO 1 4 7 2 5 8 0 3 6 9 @ CH CH # Press the SYSTEM button 2 times. The on-screen display disappears. PICTURE FUNCTION SYSTEM TIMER NORMAL !, # · When you select the channel position to AV by pressing the TV/VIDEO button, COLOUR SYSTEM mode changes in the following order: AUTO N358 PAL N443 SECAM TV !Press the SYSTEM button 2 times. @ Press the VOLUME UP ( ) or DOWN ( ) button. SOUND SYSTEM mode changes as shown on the right each time you press the VOLUME UP ( ) or DOWN ( ) button. # Press the SYSTEM button again. The on-screen display disappears. · System indication during reception <When set to AUTO> PAL B/G 5 The colour system is automatically detected and selected. [. . . ]