User manual ALTEC LANSING 416-8B LF SPEAKER

[. . . ] NÄR DENNA DEL ÄR ÖPPNAD OCH UND VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNETAUSSETZEN. NICHT DEM STRAHL AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER ADVARSEL UDE AF FUNKTION. ÄLÄ KATSO SÄTEESEEN. Caution This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain access to the inside of the product. [. . . ] Right-click the icon of the printer to be used and click "Properties". Click the "Ports" tab ("Details" tab - on Windows 95/98/Me) in the "Properties" window, select "LPT1" (or the currently used port), and click the "OK" button. To use the ALTEC LANSING Personal MFP series again, perform the same procedure but select the port to be used (for example, LPT1) in step 4. 44 CONNECTING THE INTERFACE CABLE This unit includes both USB and parallel interface connectors. Interface cables for connecting the unit to your computer are not included with this unit. Please purchase the appropriate cable for your computer. I · If you intend to use the unit as a scanner, it must be connected to your computer with a USB interface cable. The scanner function cannot be used if the unit is connected with a parallel cable. · USB is available with a PC/AT compatible computer that was originally equipped with USB and had Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP Home Edition preinstalled. · Do not connect the interface cable before installing the MFP driver. The interface cable should be connected during installation of the MFP driver. (p. 22) Connecting the USB interface cable 1 2 Obtain a shielded USB interface cable. Insert the cable into the USB interface connector located on the rear of the unit. 4 3 Insert the other end of the cable into the interface connector of your computer, or the USB hub connected to your computer. Connecting the parallel interface cable 1 2 3 Obtain an IEEE1284 shielded parallel interface cable. Insert the cable into the parallel interface connector located on the rear of the unit, and fasten with clasps. 4 Insert the other end of the cable into the interface connector of your computer. 45 5 MAKING COPIES This chapter explains basic and other copying functions. · The SPF/RSPF ( ) indicator on the operation panel will light up. If this indicator does not light up, the originals are not properly set or the SPF/RSPF is not properly closed. It is recommended that such originals be copied from the original table. · Special originals such as transparency film should not be fed through the SPF/RSPF, but should be placed directly on the original table. It can be 6 mm (max. ) at the trailing edge of the second copy of two-sided copying. · To stop continuous copying using the SPF/RSPF, press the clear ( ) key. · Copying using one-sided to one-sided mode (416-8B LF SPEAKER) : Ensure that no indicator is lit among the original to copy indicators. 1 2 Make sure that no original is left on the original table. Adjust the original guides to the size of originals. 3 Set the originals face up in the original feeder tray. Original face up 48 Stream feeding mode The stream feeding mode allows easy operation of continuous copying from the SPF/ RSPF. If the stream feeding mode has been enabled using user program No. 4, the SPF/RSPF ( ) indicator will blink approximately 5 seconds after the last original has been fed by the SPF/RSPF. While this indicator is blinking, any new originals placed in the original feeder tray will be fed and copied automatically. If the stream feeding mode has been disabled, the start ( ) key must be pressed each time the originals are set even immediately after completion of a copy run from the SPF/RSPF. [. . . ] It, like most finely divided organic powders, is capable of creating a dust explosion. 7. HANDLING AND STORAGE Handling Technical Measures : None Precautions : None Safe Handling Advice : Use of a dust mask is recommended when handling a large quantity of toner or during long term exposure, as with any non-toxic dust. Storage Technical Measures : None Storage Conditions : Keep container closed and Store in a cool and dry place. Incompatible Products : None 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Measures Ventilation : Not required under intended use. Exposure Limit Values OSHA-PEL(USA) : 15mg/m3 (Total Dust), 5mg/m3 (Respirable Dust) ACGIH-TLV(USA) : 10mg/m3 (Total Dust), 3mg/m3 (Respirable Dust) Personal Protective Equipment Respiratory Protection : Not required under intended use. [. . . ]